20 Most Recent LG 32LN530B 32" 720p LED-LCD TV - 16:9 - HDTV - Page 3 Questions & Answers

Check out these sites.... https://duckduckgo.com/?t=ffab&q=+lg+ac+inverter+showing+ch05+error&atb=v159-1&ia=web Best to you.

This will be a capacitor issue in one of the sus boards, look for bad caps or pull them and test with a capacitance tester.

Wifi as Bluetooth is no more available in television anymore

Question edited for clarity. Didn't we answer this before a week or so ago? Here is the service manual https://www.manualslib.com/manual/946933/Sanyo-Dp32649.html?page=4 ..

This wouldn't be a HDMI issue, you would have the problem on all the screen if that was the issue. On the left side of the TV (looking from the back) there will be some narrow long boards, some models use 2 some use 4, those are the scan driver boards, chances are that's where the issue is at. It's normal for those to work for awhile when the set is turned on, you could switch them around and see if the issue goes from the top to bottom to confirm this is the issue.

First off, 126 vdc is the backlight B+ voltage using frame as ground, if you measure across the + and - pins on the plug with it connected you should be seeing a couple volts if the backlights are bad, what's happening is the inverter overload is shutting down the minus side, you will always see the hot side voltage of around $125 vdc if the inverter is working. Very good chance you have bad LED backlights as they are known for failure on this and a lot of other LG model sets.

Don't suppose you have a re-flow oven. If it worked for awhile after soldering on the main board I'd try re-flowing the entire board, sounds like some cold solder joints if it worked for awhile after soldering. Not sure how a grounding issue would make half the picture have issues however but anything is possible.

Where is a CCA (charge coupled device) found in a LED TV? I've repaired thousands of LED TV's and have never replaced a CCA, nor found one on a LED TV.These are common in video cameras but not TV's

The LG AKB73615337 remote control is designed specifically for LG TVs and may not be compatible with the Xfinity Flex box. However, you can try the following steps to see if it works:

1. Ensure compatibility: Confirm that the LG remote control is compatible with the Xfinity Flex box by checking the list of supported devices in the remote control's user manual or by contacting LG customer support.
2. Power on the Flex box: Make sure your Xfinity Flex box is powered on and connected to your TV.
3. Activate pairing mode: Put the LG remote control into pairing mode by simultaneously pressing and holding the "Back" and "Home" buttons for a few seconds until the LED light on the remote starts blinking.
4. Follow the Xfinity Flex box pairing instructions: Refer to the Xfinity Flex box's user manual or contact Xfinity customer support to find the specific instructions for pairing a remote control. This process may involve entering a pairing code or following a series of steps on the TV screen.
5. Test the remote control: Once the pairing process is complete, test the LG remote control to see if it works with the Xfinity Flex box. Try navigating the menu, changing channels, adjusting volume, and performing other functions to ensure proper functionality.

If the LG remote control does not work with the Xfinity Flex box or if the pairing process is unsuccessful, it is recommended to use the original remote control that came with the Flex box or consider purchasing a universal remote control that is compatible with the Xfinity Flex box. Universal remote controls are designed to work with multiple devices and usually come with instructions for programming them to work with specific devices. Remember to consult the user manuals of both the LG remote control and the Xfinity Flex box for specific instructions and contact customer support if you encounter any difficulties during the pairing process.

Just for information, we are Fixya dot com, we are not LG Support or Dell Support. It is possible to connect the two. The Dell has an HDMI 2.0 Port. All you have to do is connect to the television and then use the Source button on the television remote to the numbered HDMI socket on the television where the cable is in. https://www.google.com/search?q=dell+latitude+5330+using+hdmi+cable+connect+to+lg+smart+tv

The power supply is bad or problems with the screen or with the the LCD.

Buy a new TV, water and electronics don't mix

I assume you changed all the LED strips when you changed the bad ones, NEVER replace part of them, if you didn't replace them all, open the set up again and replace the ones that weren't replaced the first time and all will be well.

If the HDD is corrupt or had damaged tracks it will not innitialise and the rest of the system will not complete power on.

Try a power Reset first before delving deeper.

Question edited for clarity. https://www.fixya.com/support/r29872378-universal_remotes_no_facsimile_remote

LG Blu Ray Player Remote Control Codes

directutor.com https://www.directutor.com > content > lg-blu-ray-pla... Here is the list with the KNOWN working device codes for LG Blu-Ray DVD players. These should work with ANY remote as these remote codes are universal.

LG Blu-Ray Universal Remote control codes

myuniversalremotecodes.com https://myuniversalremotecodes.com > lg-blu-ray-rem... May 29, 2020 - 4 digits LG Blu-Ray Universal Remote codes · 2339 · 2352 · 2270 · 0741 · 1602 · 2371 · 2303 · 2368 ...

Likely to be the power board, but read this... https://www.fixya.com/support/r29790007-repairing_own_television A good option is to buy a 'board repair kit'. ..

Hi Jimmy, it's unfortunate that you threw boards at the set without doing some troubleshooting, you have bad LED backlights, it's a common issue for the model set you have, new strips can be ordered from shopjimmy.com and installed yourself, use extreme care when handling the panel.

Here is the Board Kit for the set. The switching on and off is likely to be the power supply. WiFi issue if likely due to interference, where the television is located and a weak signal. Connecting via Ethernet is always preferable. You can swap boards out and see if it improves the blue tint. https://www.google.com/search?q=lg+43uh6030+board+kit+replacement Our Television Expert is 'Larry'. He may drop in soon. ..