20 Most Recent
RCA Scenium HDLP61W151 61 in. HD-Ready Television - Page 5 Questions & Answers
MY HD65W140 NO PICTURE NO SOUND NO POWER. STARTED
hi Amelero, looks like your TV power supply board is shorted, this happens when high voltage peaks and unusual power outages occurs, it needs to be checked thoroughly, Usually the power supply board is completely replaced, so check out first your dealer if its is on warranty, else call for service, I don't recommend tinker with it, its so sophisticated that even us tech guys gets headaches so we replace the entire board. These also goes to other experts too.
There is still possibilities to repair the fallen board but this method takes time.
I have an RCA Scenium. When I turn power on it
it may just be components on the power supply board have small breaks that keep power from flowing until the board warms up and the breaks are closed.
This repair will take someone with a knowledge of your tv and a good eye to inspect the circuit boards. The plus side...it should be a simple fix once the breaks are found. Keeping costs to a minimum.
Good luck and be careful
My RCA Scenium picture just went black out of no
Take the Lamp out and see if it is shattered. The access door is on the left rear of the set. Chances are the lamp is the problem. The Lamp cage has the part number on it.
I hope this helps,
Skyassoc
Our Scenium HDLP5W151 TV Is dark and the lighting
Bad Light Engine part# 261589 $800.00 Call UED for price of rebuilt one 1-800-648-6657 First Look on the power supply board and see if you have any bad capacitors if you see any that are puffed up on top they are bad. 1000uf 16v 2200uf 25v If everything looks ok then it will be the light engine.
I currently have no sound. It comes back every
Let verify first to narrow down to where the problem can be, attach the powered PC speakers to the Audio Line out RCA jacks to see if you can get the sound there, if you do, then the problem can be in the power amp circuits, if you do not get the sound at RCA jacks, then the problem can be in the sound processor circuit. Please post back what you find.
Rca scenium 61 inch
Hi
Thanks
for using FixYa. From what you have described I think that there are a few
different things that can cause this. The first thing I am thinking off is that
the flyback transformer has gone bad. Other possibilities include a fluid leak
from one of the picture tubes (these tubes have a coolant in them and the seals
are known to break and leak onto circuit boards)
and finally I think you should also check the deflection board and signal board
as they might be faulty. I have also heard that in these sets the chassis was
brought over from Germany
and wasn't ever fully converted to American systems. It is only recommended to do it
yourself if you have electrical expertise and know how to solder/re-solder
components. If you get it repaired from an authorized repair center then it
would cost you somewhere around $200-$400.
Please do accept the solution if
the issue is resolved or else revert for further assistance.
Thanks
Rylee
When my screen is blank,
Its a good possiablity that the Light engine is the problem, first Ck over on power supply Board if you do not see any Bad capacitors sometimes this will throw you and can cause problems in video. Chances are it is the Light engine Encompass Parts Distr. Lists your TV But has HDLP61W151yx or 2 yx or 3 yx or yx4 Go by the model number that is yours it will be on back of TV then once you know which one it is Go to Encompass online or Call 1-800-638-3328 find out correct Light Engine number They list the yx1 Part# as 263223 this one List for $769.00. OK heres another company that sometimes Gives return DUD FEE for your old Light Engine and it makes it cheaper UED Call 1-800-648-6657 and Try E-Bay under Electronics I have seen some good deals on Light Engines thier with Good warranty as well.
Sound with No Picture
If the lamp hasn't been replaced I would suspect it first. Depending on your full model number of your TV will determine the lamp you need.
Model HDLP61W151YX1 = 260962 LAMP
Model HDLP61W151YX2 = 265103 LAMP
The sticker with the model number will have a service model number that will include the YX! or YX2 at the end of it.
Please take a few moments to rate my answer. Thank you.
I have a computer with HDMI output and my Scenium
(No longer listed on Amazon.) The most likely reason for no display is not matching the scan rates. Your TV is either 1080i (1920x1080x30) HxVxrate or 720p (1280x720x60) high definition. That's its native display but it may accept both but not 1080p. The computer must be set to one of those. The TV will not accommodate, well it may accept 480i or 480p (720x480x30 or 60) for standard definition and that could be 640x480. Go to your computer display controls and see which resolutions are available and it may be different in mirrored versus extended mode. If the signal comes from a TV DVI source and is converted to HDMI, it will not include sound. There may also be a problem with copy protection (HDCP) as your computer may be fussier than the TV.
-Ken
Not finding what you are looking for?