Casio Privia Px-130 Px130 88 Key Digital Stage Piano Nu - Answered Questions & Fixed issues

You can download the service manual for free from manualslib.com

Lose up the power button

ask casio directly or GOOGLE it

recommend electronic component store. not sure which country you are from ? in Australia Jaycar You will need desolder braid https://www.youtube.com/watch?v=htrcZuK_ZsY https://www.adafruit.com/product/149 You will need solder you will need a soldering iron https://www.youtube.com/watch?v=oqV2xU1fee8 you need safety glasses you need a steady hand You can either remove the component first and take it to the electronic component store to find a replacement part or take the piano to the store and open it up and show them the part you need to replace. electrician will most likely not be the right person an electronic technician as the socket will be for a low DC voltage plug from an AC - DC adapter most likely.

Insidr near whete you plug the power in

http://www.circuit-encyclopedia.com/listinfo-67-111.html Download Service Manual for PX-410R as PX-410R is the same model as PX-575r.

factory reset Procedure. Turn the keyboard off then press and hold the TONE and FUNCTION buttons while you turn on

I would unscrew the case to fix it only if it is out of warranty. Take it back to the dealer. Casio gives 3 years or 5 years warranty depending on the country.

Make sure you follow the steps of the procedure below exactly. Connecting incorrectly can make data send and receive impossible. 1. Turn off the digital piano and then start up your computer. • Do not start up the music software on your computer yet 3. Turn on the digital piano. • If this is the first time yo u are connecting the digital piano to your computer, the driver software required to send and receive data will be installed on your computer automatically. 4. Start up your computer's music software. 5. Configure the music software settings to select one of the following as the MIDI device. CASIO USB-MIDI

First is to borrow/buy a new AC adapter to test. Adapter power cable could be broken or internally shorted because of the tripping

Old reply so hopefully it's fixed. Dust or hair can get through the gaps and land on or near the contacts of the electronic key sensors. To be on the safe side (rather than doing a diy) take it in to the technicians. They'll have it fixed in a jiffy

Check the midi channel. It needs to sync to FL Studio. Channel settings you'll need to look up in the privia manual...can be laborious - but worth it in the end :)

YES. Either plug in headphones into the headphone socket. There should be a switch on the back which disables the speakers as well. A simple ON/OFF switch for speakers

You might chek if one of the buttons MIGHT bee stuck down confusing the processor in it. Do a factory reset as well.

In a word, NO. They simulate weighted keys by adding spring force and inertial weights. It gives a more realistic feel, however it is stiffer, more like an acoustic piano. You will develop strength and get used to them... If you have been used to playing some synths that are not hammer weighted these keys will seem very springy.

The unit will have to be opened and the key restored to the normal position. Most have a spring, sometimes a leaf type that holds the key up and locked in. When opening the unit care must be used as there are ribbon cables between the halves of the cover.

First thing is to verify if the sound is there using headphones. This is important test as it isolates problems in power amps and other connected equipment that may be sensitive to the particular pitch of those keys. If it is in the headphones, then likely you will have to take it to a repair shop as the problem would be very deep in the unit's sound generator hardware.

One of the two contacts for that key is not working. This could be dirty or damaged contact. They use a conductive rubber pills that the key presses against circuit board traces. One contact makes before the other and this is how velocity is sensed. Unless you are adept at this repair, I would recommend you take it in for repair. Chances are any part cost is negligible... mostly labor to open and access the contacts for cleaning. Clean ONLY with 99% isoprophyl alcohol and Q TIps... VERY GENTLY.

Test the adapter with a meter... Most probable cause is a bad power connector. Often the solder at the input power connector breaks loose is only problem. If you are not electronically adept, best to take it to a shop.

I SUSPECT that the USB connection is ECHOING the data, causing multiple generators to be active. Those extra ones then are mixed into the line out of the keyboard. In your PC, make sure the echo setting is turned off, OR disable the sending out of audio via the USB. Alternatively, DISABLE MIDI/USB incoming to the keyboard.