20 Most Recent
Sharp 25R-S100 25" TV - Page 3 Questions & Answers
I HAVE DONT SOUND
check speakers or audio ic and voltage on ic should be 12v if there then ic defective.
Looking for th remote codes for sharp tv model,
HelloThree digit universal remote codes for Sharp TV are:004/ 009/ 079/ 095/ 111/ 112/ 114/ 122/ 123/ 124/ 173 Four digit codes are:0079 0123 0063 0020 0004 0009 0226 0266 0006 0095 0122
Direct Code Entry
- Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
- Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
- Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
- With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
I have a Sharp 32"
try checking the system for timer or sleep mode operation try to setting it off
What does opc stand for
Optical Picture Control. It sets the brightness of the television according to the brightness of the room you're in.
Primo sharp 21v-L70m model the
These sets are quite outdated, there are fewer and fewer repair shops out there for them.
The problem is most likely the power supply (internal), this can be repaired quite simply if you know what to look for. Other problems may or may not include a blown IC, fuse, lamp, or the tube itself.
The cheapest option you've got is to buy a new TV I'm afraid.
What type of port does this have at the back?
Hi:
The only port on the back of this model is a Composite Video input, for connecting a VCR/DVD etc. Their is also the coax cable connector, you also have a video input 2 in the front of the set for connecting even more video accessories..
Sharp t v 25r-s100 no
This can be caused by one of two problems. EIther the fuse is blown which is located inside the rear panel next to the power supply aka power inverter. Or the power inverter/supply itself is bad if the fuse is good. It can be tested with a voltmeter.
I have a TV sharp
Hello
The TV you have bought from Belgium, Sharp 25R-S100_ model can only recive NTSC [National Telivision System Commitee], signals only. It is not a multisystem compactable one. In France, the telivision boradcasts are in SECAM system I thinks and knows. [It is known as Sequrntial Colour and Memory]. The TV you have bought will work in US and other countries like that, where there transmission sytem is NTSC. I don,t know whether in France there is TV stations transmitting on NTSC system. If have, your TV will receive that transmissions. It is a system compactibility problem.
If the matter is so, nothing can be done to receive programmes transmitting in SECAM system. If a system convertable device is available in France, that is SECAM to NTSC system converter, you can connect it according to the instruction manual come along with that device.
Your TV is capable of receiving 181 channels and have PLL[ Phase Locked Loop] channel locking system, but have only capable of receiving NTSC RF signals. Ok
Sharp 25R-S100 25RS100 SHARP 25" STEREO FRONT/REAR AV
Good day.
Try to check the crt socket. Also, check for the loose contacts along the Chroma IC. Like wise, there is a screen adjustment on the rear portion of the flyback. Try to adjust the screen.
Response is highly appreciated.
chris
The remote will not work, I have put new
If the buttons work on the tv, it sounds like the infra red receiver board has gone faulty. This is located on the bottom front of the tv behind the lens on the front. if the tv is in the prescence of a smokng environment sometimes the infra red led gets contaminated and needs cleaning. Otherwise, replace the pcb. If the buttons on the tv dont work then it may be either a connecton to the main pcb or a faulty main pcb.
Not finding what you are looking for?