20 Most Recent Philips 60PP9202 60" Rear Projection HDTV-Ready Television - Page 3 Questions & Answers

The problems ur tv having is also parts of the tv Convergence board are dead,but it is totally dead to causes this problems,if convergence board it still have some functions left.Tv will only have colors R,G,B will mis alignments,have colors shadows pictures and 3D pictures look alike,but convergence board are not getting any voltages at all that why u just hearing faint chirping noises that it.The tv convergence board,must require to changes 2 STK convergence ICS and some or all of it resistors too.For the covergence board have fully functions again to solved this problems.The shop will cost u like $300-350 for parts and labors.

Its the flyback.....but nearly impossible to find.

Your convergence has failed and needs to be repaired. Once quick test is to goto your convergence menu and see if you can adjust red and blue. If not its has failed and needs to be fixed. You can call in a repair shop or you can get the parts and instructions from www.TvRepairKits.com and do the repair yourself. Its a fairly easy DIY fix. Here is an example video You-Tube video "9oI1Nzq7CR8" placeholder (do not delete)

if its a Philips as indicated here that model has no reset--if picture looks 3d etc for model listed here it is a convergence problem.

no lamp for this model, it uses three picture tubes but the three D looking picture is a convergence circuit problem and is fixable.

Sounds like one or both of your IC chips burnt out. You will need to replace them. A good place to purchase high quality IC chips is convergencechips.com.Be careful there are a lot of fakes out there that don't last and cost you more money in the long run.

Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Below are more details for both items. Also, complete repair kits with instructions and repair support are avail from site such as www.TvRepairKits.com Common Problem #1) Convergence has gone outProjection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem. Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. The power light will blink. TV may also make a chirping noise.

Here are some pics of convergence problems. SOLUTION #1What you will need to do is convergence. You can get a repair kit from TvRepairKits.com . It includes replacement parts,step by step instructions, support, etc.Common Problem #2) CRT Fluid is CloudyProjection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images. Picture of a set that needs the fluid changed. TV set after fluid change SOLUTIONWhat you will need to do is replace the coolant and clean the crt. You can get a repair kit from TvRepairKits.com . It includes replacement coolant,step by step instructions, support, etc.

• Print
• Email
• Flag

Problem with Hitachi 51F500 51 in. Rear Projection HDTV-Ready Televisioni want to learn how to do convergence on my tv its a hitachi rear projection i have problums with colors not aligning,could you lead me in the right direction ps: i don't have the remote so i

can't magic focus

Posted by ejaparks on Mar 03, 2011

• + Add a Comment
• Suggest a Solution

AdChoicesMajor Appliance Repair

www.graysoncollinapplianceandac.comResidential/ Commercial, all brands Friendly, knowledgable technicians!Get $75 of Advertising

www.Google.com/AdWordsPromote Your Business On Google. Claim Your $75 Coupon Now!Solutions (1)

Your convergence has failed and needs to be repaired. Once quick test is to goto your convergence menu and see if you can adjust red and blue. If not its has failed and needs to be fixed. You can call in a repair shop or you can get the parts and instructions from www.TvRepairKits.com and do the repair yourself. Its a fairly easy DIY fix. Here is an example photo....

dEAR sIR:

Turn on the TV set, bring up the convergence menu and make sure the three colors--red, green and blue--converge and overlap at the cross in the center of the screen. This is needed to help converge the TV later. Turn off and unplug the TV.

2

Remove the front screen by popping off the bezel and pulling the three combined screens out. Place wide cellophane tape around the frame to prevent the three screens from separating. Lay the screen someplace where it won't be bent or scratched.

3

Remove the circuit board from the bottom of the CRT neck. It may be held in place by one screw or glued in place with silicon. Pull it out without twisting it.

4

Disconnect the large red wire from the high voltage transformer by grasping it with a large side cutter and rocking it from side to side to lift up the fastener. Disconnect the two bundles of wires from the main circuit board and leave them hanging from the CRT.

5

Remove the ground connectors by releasing their tabs with a narrow screwdriver.

6

Remove the CRT assembly from the TV by removing its four flat-bladed screws and pulling it out of the TV. Lay the CRT down with its filler plug facing up in a location far away from the TV's circuit boards.

sincerely. God bless you

ernesto cuaddra

managua, nicaragua

Replacing the convergence board will require a complete convergence adjustment. A better solution would be the replacing of the defective convergence IC. This would retain the convergence settings for the set. I'll locate the part numbers and costs and update this later.

Dan

the problem on you tv is the convergence ic , this part need to be replace part # stk392-120

Good day!!!! I need to know first if your TV is on standby mode (red LED lit) or not?..If the green light lit your TV your high voltage (HV) is switch but you have open line on heater that cause of no picture and the sounds is chirping because of analog(antenna)/digital connection or bad audio chips..I need this information above for specific diagnosis and to prevent more damage and failure..Also I need this information to avoid mistakes to buy a parts with no help...also I need the model # because on my tread there are 2 model # which are correct? is it 60PP9202 60" or 55PP8620?..for specific diagnosis and for possible get a diagram..Thank you very much for choosing my service!!!!Rossiel Gomez (nineng)

Something easy to try: with set unplugged remove back cover and locate the three large lens (black plastic housings) and clean the lens with either a lens cloth or a paper towel with glass cleaner sprayed on it.The lens are your light source and if dusty the picture will be darker and look somewhat dull.Let me know if you have questions.SD TECH

check out in inverture board the part that powers the light bulb or the light blub is bad

Is It the screen (the plastic/glass) or the picture that is bowed? If it is the front screen, you just need to re-install the screen in the frame. If it is the picture you need to get the projector re-aligned.

Here are some of the most common symptoms and example photos of a convergence problem

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.

Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.



You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.

Solution #1

You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick note and they will put one together for you. Their kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, etc.

Are you getting some kind of high pitched squeel from set when you try to turn it on?The more you tell me the more I can help.

The lamp can cause a dark picture if it is defective. There is an access door to the lamp. Take the lamp out and inspect it. Especially at the bottom of the center stem where you may see a bubbling of the glass. If so it is bad for sure. Other problem could be in the main board. For good price on lamp with housing go to pureglare.com and enter the model number.