20 Most Recent
Sony KP-46WT510 46" Rear Projection HDTV - Page 5 Questions & Answers
My television is plug to
I also have this set. Try pressing the TV/Video button on the remote several times to go through all the inputs available. On mine there are 4 input sources, the antenna and 3 others. You may have accidentally switched to one of the unused inputs.
There is a yellowish tint in one corner of the
the problem u have is the convegence ic , try to do auto focus , if this dont work , u need to replace the convergence ic , stk392-560 - or 392-040 , but i would recoment to hire a tv tech because to replace this part u have to take everything apart and this wires are not mark , normal repair on this unit is about $250 - 300
My television is only 6 years old. Red lines have
Tv have a problems known as a convergence problems,it dead.The tv have colors lines R,G,B mis alignments,have a colors shadows or 3D pictures look alike?Ur tv convergence board have dead 2 STK convergence ICS and some or all it resistors too.These parts on the tv convergence board,must be replaced to solved the tv picture convergence problems.The shop,will cost u like $300-350 for parts and labors.
All the lettering on my screen as well as images
Tv have a problems known as a convergence problems,it dead.Tv have colors lines R,G,B mis alignments,have colors shadows pictures or 3D pictures look alike?The tv convergence board have dead 2 STK convergence ICS and some or all it resistors too.These parts on the tv convergence board,must have to be replaced to solved the tv pictures convergence problems.The shop,will cost u like $300-350 for parts and labors.
Focus is off
Focus is off, then it needs to be converged, or the convergence IC needs to be replace, if the red, blue , and green will not line up. If the convergence is OK, then and just looks out of focus, then it might just need a good internal cleaning.
We lost password parental how i can reset it
Sense you lost the password you can type the master password on the screen the master password is 4357. That will override all the settings.
Also if you need the manual please ask I will forward one to you.
Good Luck
MY SONY PROJECTION TV DOESN'T WORK. IT BLINKS 10
I prefeer you go to a tech with this problem beacause of highvoltage. Your problem is siple though the red light flash is an error code that means your bulb is blown in your set. This is the bulb that illuminates your screen. Bulb cn cost up to a $100.00 for one so please shop around if you are a do it yourselfer. Once again I stress please take it to a tech if you are not electronic savvy
When tv get turned on, it was just red and
So I supposed the LED starts blinking after it shuts down. Can you please tell me how many times it blinks in between each pause so that I can tell you what the problem is?
Sai.
My sony kp57ws510 model tv has double vision and
The tv have a problems known as a convergence problems,it dead.The tv colors lines R,G,B mis alignment,have shadows pictures or 3D pictures look alike.The tv convergence board have dead parts.The 2 STK convergence ICS and some or all it resistors on the tv convergence board are dead.These parts on the tv convergence board,must be replaced to solved the tv picture convergence problems.The shop,will cost u like $300-350 for parts and labors.
My Sony KP-46WT510 is not working. The code
Projection TV sets are known to have two common problems. The first problem that is common to these sets is convergence failure. When this happens the TV will usually look 3D, Wavy/Distorted, etc. It may also shutdown and blink an error code.
The second common problem with Projection TV sets is dull video, halos around objects, white looking video, or red overpowers the screen. This is commonly caused by the fluid in the lens being clouded over.
You can find more details and solutions here on Fixya at the following link below. Or click HERE
http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull
One horizontal line center on the screen
The vertical deflection circuit has failed, or has been shut down by a service code entered from the remote control*. Usually you can get out of service mode by turning the set off and on again.
*Normally, you have to enter a special combination of front panel and remote control codes to get into service mode, then enter another code on the remote control to get the horizontal line. The horizontal line is used for adjusting the screen controls for each color so you get proper color in the dark areas of the picture.
The colors red green and
Hello,
The problem is from inside the unit of the television. Mainly a bad lamp, most rear televisions have about 2 or thee lamps, so what you have to do is to open up the television, then assess the lamps after doing that you will find the faulty one.
All you need to do is to take it out, get a replacement for it and fix it in the way you took the old one out.
Take care and good luck
Blurry picture. Red & green
Not any amplifiers problems.The problem u having it known as covergence problems,it dead.The tv colors lines R,G,B mis alignment,have colors pictures shadows or 3D look like pictures.The tv convergence board the 2 STK convergence ICS and some or all it resistors are dead.These parts,must be replaced on the convergence board to solved the picture convergence problems.The Shop,will cost u $300-350 for parts and labors.
Screen has red outline
One of possible 2 things. You can go into menu and try and adjust the red convergence settings and hopefully that will take care of it. It possible if it wont adjust that one of the convergence ic chips has failed or could be a weak picture tube. Try adjusting the red convergence and hopefully your problem will be solved. Check you owners manual if you have trouble but its not to hard..
Not finding what you are looking for?