20 Most Recent
Sony KP-46WT500 46" Rear Projection HDTV-Ready Television - Page 5 Questions & Answers
Replaced a convergance chip..(ps8003) now tv
hello
Eight
GA_googleFillSlot("TL-IMU-Article");
blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the self-diagnosis code. Check IC406 audio amp, PS401, and 402. On some projection models of Sony TV sets, this code means that T8005 (
flyback transformer), or the associative components in the high voltage circuits are defective on the D board
regards
shaun
Hello.. I need to replace the red bulb on my sony
You can get it in the below places..
Kmp electronics
50 Freeport Blvd Ste 9
Sparks, NV
(775) 355-8273
Service west electronics
1320 E Plumb Ln
Reno,
NV
(775) 825-6133
Circuit city
4811 Kietzke Lane
Reno,
NV
(775) 827-5011
I have an IC convergence failure on my Sony
hello you need 2 of them also you will have test the resistor in front of the ic and capacitors near by also if you haven't used a soldering iron before you may find it difficult it's a lot of hassle. ps try youtube it may show. you good luck
regards
shaun
Tried to use 2002 Sony
Hi,
Symptom shows that it is convergence out chips failure that causing misaligned images on screen. Please replace convergence out chips in tv to get converge picture.
Question shows it is Sony KP-46WT500, if it is different model let me know please.
I can provide you more technical assistance if you wish to repair tv by yourself.
Thanks.
My kp46wt500 serial # 9018171 comes on green ,then
Hi,
8 times red light blinking shows problem with High Voltage section in TV.
Let me know about green and blue symptoms, does TV show high bright green then blue screen with few thin retrace lines then shuts off and red light start blinking?
Is that the problem?
My Sony KP-46WT500 screen shows the tv image in
It is rear projection TV that use 3 picture tubes of red-green-blue to show color picture on tv front screen.
Do you see standby red light blinking when TV shuts off after showing blue image for a while?
If red standby light is blinking, please count it how many times it blinks, there would be 3 seconds pause between blinks so count pause to pause and post it here to find out possible solution.
Thanks.
I have Sony KP-46WT500 Projection
Hi,
It would be great to assist you in Sony convergence issue.
As you said, for some time TV shows bad convergence in picture that shows its matter of lose/ dry solder joints in D board, specially on convergence out ICs pins that need to be re-solder.
There are 2 big black ICs mounted on aluminum heat sink on D Board of TV, below image shows D Board location in TV.
Resolder pins of these 2 ICs and also check any other dry/ cold solder joints in circuit board. I do not think of IC replacement as problem occurs some time.
Let me know if you have additional question.
Thanks.
I just replaced stk392-560 chips but didn't work.
Allot of people make this same mistake. Odds are you got the CHEAP china chips. Those do not work in sony TVS. Only the ORIGINAL sanyos will work. If you payed less then $20 each, they are not original. You can also go to sony.com. Get your board number and check it under parts. IF it says $65 you can get your board rebuilt by sony. Just call in to make payment and get a work order number. I send in allot of these boards. They are returned 2 day fedex express. I guess sony feels bad for selling this junk. Check you cross convergence. If you can move any of the colors, its the chips.
Red ghosts in mod kp-46wt500 sony
Go into the customer menu and select CONVERGENCE and look to see if red or blue lines are skewed and or will not adjust in some direction.
If this is what you find--you have a convergence circuit problem.
Let me know if this is what you find and I can tell you what parts need to be looked at and replaced and I can give you general instructions about what you will need and the best place to find them.
Rate this solution if this information has helped you as I do this here for free.
SD TECH
Sony kp 46wt500 has 3d screen what might the
If convergence out ICs got defective then TV shows that kind of picture.
Replace IC8001 and IC8002 on D Board, both big black ICs are mounted on aluminum heat sink and number STK392-560 would be written on it.
Required ICs are available in
Part Store, click that link to see an image of IC and price info.
If you are not comfortable with soldering parts in circuit board, call local tv tech to replace it.
Thanks.
Ghost on the screen, blue in color
Did you check the six 3.15 amp pico fuses on the D board in line with the resistors and the two 5 amp picos on the G board? Usually one or more of the Picos will blow especially on the G board
Sony 50" Projection TV problem
this set is getting up in years you have a weak CRT that is shutting down the pix
sony has what is call an IK curcuit that wants to see equal outputs on the crts so youget true color any way you need crts not avail anymore sorry
Not finding what you are looking for?