Sony FD Trinitron WEGA KV-36FS120 36" TV - Page 7 - Answered Questions & Fixed issues

You must press the "display" button on the actual remote control--that is the only way!

amazing was just fixing an older tv then noticed the old 3.5 phono plug ( used to be fro ear phones) said to my one of my techs i havent seen one of these for years then we started talking about how stupid it is that they dont put them on tvs anymore and how could we make one the old way was to run a wire into the set and install an external 3.5 phono our selfs sadley this is still after much arguing the only option


take care

sonic boom electronics

I've uploaded it for you to a site:
http://data.hu/get/3342921/sony_kv-27fs320_32fs120_32fs320_34fs120_36fs120_36fs320_38fs120_chassis_ba-6_ET.pdf

I've also saved it to my computer, so if it's not working write me a message, and I'll send it to you via email too.

Hope I could help.

Gabor from Hungary

hi,
check for any dry soldering in the circuit board , on power supply side and horizontal output side.
ok

i need some details to properly answer and fix your problem Thank you

hi,
when u replace the str 6107 along Whit it ,replaced the opto-coupler, the polistor , ceramic capacitors in the str side. mainly that one connected to is pin 3.
on the out put side replace the SE1XX voltage controller also.
ok

I had a similar problem with my 42 in Philips LCD HDTV.

Here was the problem. My Power Supply Board had several bad capacitors. I opened my TV (warranty was expired of course) and found four bulged capacitors on the PSB. Many major electronics companies Philips/Magnavox, Sony, Panasonic, and others were sold capacitors that failed in 2-5 years instead of 10-20. The capacitors fail prematurely due to a lack of preservatives. Unfortunately, they were installed in all sorts of devices and cause a wide range of failure problems.

Here are some options for you.

1. Have it fixed by a professional $$$$$$$??????? (Is it under warranty?)

2. Open your TV and find PSB. (The board that the power cord plugs into) Check for faulty caps. If you find some (bulged or leaking) bad caps replace the entire board. The entire board costs around $250 right now because they are in high demand right now. They can be found at tv-part.com but supplies are limited. I would definitely shop around though.

3. Remove and then replace individual faulty caps. This takes some soldering skill.

Caps are inexpensive and if you can take care of it yourself it will save you hundreds.

I have a tip/tutorial on this site that may also help. It gives step by step instructions for replacing caps on PSB #715t2432-2. If this is your board you are in luck. It's called: Fixing the Philips Turns/shuts off on its own problem. I'm working on uploading pictures to help guide people though the process as well. Let me know if I can do anything to help.

Hope this helps and Good luck.

Kaufman605

I had a similar problem with my 42 in Philips LCD HDTV.

Here was the problem. My Power Supply Board had several bad capacitors. I opened my TV (warranty was expired of course) and found four bulged capacitors. Many electronics companies were sold capacitors that failed in 2-5 years instead of 10-20. The capacitors fail prematurely due to a lack of preservatives. Unfortunately, they were installed in all sorts of devices and cause a wide range of failure problems.

Here are some options for you.

1. Have it fixed by a professional

2. Open your TV and find PSB. Check for faulty caps. If you find some (bulged or leaking) bad caps replace the entire board.

3. Remove and then replace individual faulty caps. This takes some soldering skill.

Caps are inexpensive and if you can take care of it yourself it will save you hundreds.

I have a tip/tutorial on this site that may also help. It gives step by step instructions for replacing caps on PSB #715t2432-2. If this is your board you are in luck. It's called: Fixing the Philips Turns/shuts off on its own problem.

Hope this helps and Good luck.

Kaufman605

The Power/High Voltage board is the main cause of this. Most of these boards must be sent to Sony to be refurbished because Sony no longer manufactures the board.
I hope this helps,
skyassoc

Hello

Three digit universal remote control codes for Sony are:-

002/ 006/ 071/ 128

Four digit universal remote control codes for Sony are:-

0128 0013 0002 0071 0380 Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.

1. Manually turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
5. Press and release MUTE to install the code. The indicator light goes off.

Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search. OK.

Instructions

1. 1 Make sure the power cord is properly plugged into a wall outlet if your TV is not powering on.
   
2. 2 Make sure the video and audio cables connecting your TV to external devices are secure if you are experiencing a fuzzy picture or no picture.
   
3. 3 Reset the parental password if you forgot the password and are unable to view certain programs. To do this, click "Menu" on your remote control and use the arrow keys to select "Parental Controls." Enter the master password, which is "4357" to reset the password.
   
4. 4 Turn off the caption vision option if you are seeing a large black box on your screen. To do this, click the "Menu" button and select "Setup." Select "Caption vision" and press the "Plus" button on your controller to set the option to "Off."
   
5. 5 Check the "TV/Video" setting if you're not getting a picture on your screen. You may have inadvertently selected a video input that isn't active. Press the "TV/Video" button on your remote to cycle through video inputs.
   
6. 6 Alter the brightness settings if you are experiencing a poor picture or no picture. To do this, press "Menu" and select "Video." Increase the brightness settings to see if the picture begins to appear.
   
7. 7 Make sure the volume is not muted if you are experiencing a clear picture but no sound. Press the "Mute" button on the remote control to turn mute on and off.
   
8. 8 Power cycle your Sony Wega if it's frozen or not responding to your remote control. Unplug the power cord and wait a few seconds. Plug the power cord back in.
   

You either have problems in the power supply or the horizontal output transistor and maybe flyback transformer have failed. If your not familiar with electronic using a multi-meter it will be near impossible to isolate which area has the problem..

Repairs on those tv vary by location but a reasonable average would be 90-120 on the low side and 150-180 if the flyback has failed.

Sorry for the bad news.. Wish I could have said unplug it for 5 minutes and say a couple of chants and walla its fixed..

Good Luck

If u move the tv pictures come back on clear and good,no bruses to the pictures at all?Yes,this tv can be fix the PCB main board is cracks or borkens,could be mend to it by steal rods and solder joints by a tv tech. to fix it.But if the pictures have bruses in it.The tv picture tube is damage,sorry this tv garbage,not worth fixing.

Hi,

You are correct, the switch would still click even if something major had failed inside the TV. There is a small microswitch inside the TV directly behind the on/off button. The microswitch can break or get stuck and there is usually no way of fixing it without taking the back off the TV. You could try repeatedly pressing the on/off switch rapidly as this can (very) occasionally unstick it, but it's probably broken.

This isn't generally a user replaceable part as the actual switch is soldered to the PCB. I would take it to a TV repair shop, but if you are planning to remove the back of the TV, make sure it's unplugged and don't open it until the power has been off for at least half an hour as you can still get a considerable residual current shock!

Hope this helps.

Regards,
BElectric

Hello
You just count the number of blinks of the standby light before it goes out to green. In sony sets this blinking count ic critical for us to locate the faulty stage. You just count it after switch it Off by Power switch and Switch it On by the power switch at the front of the TV, for at least three or four times, and make sure abut the number of blinks, and report it to me. Ok

Hello
In Sony TVs, number of blinks of the standby light denotes some problems inside the circuit board of that TV. The number differes with the section where the fault is. According to the number of blinks, we can reach to fault point easly. Just count the number of blinks, with TV switch On-Off with its front panel switch, not by the remote control. Keep this in mind. Ok.

If you have a remote control access your system menu and press automatic channel search. Wait until all the channel has been loaded. Once finished you can now use the up and down channel search button of your remote control.

ICs in power supply, will have to have a shop do it. expect to pay around $150

Hello
I thinks that you need to set its colour and other parameters, and posted this problem. If so there is adjustment at the first "Menu" option itself.
Press "Menu" button on your TVs remote control. You will see "Video" function as first selection on the screen. Use "Prog Up or Prog Down" keys to select and hilight the desired parameter. Use "Vol up or Vol down" keys to change it as your taste. That is all.
Normally the "Contrast should be more that 55% to 60% of its total value to get a clear and vivid picture. Colour and brightness are according your individual taste. Ok

If you wants to reset your TV to factory settings,
Turn on the TV.
Hold down "Reset" button on your remote handset and keep it pressed.
Press and release the power button on your TV front panel. the TV will turn itself off.
Release the "Reset key". Ok

Hello
There are so many transistors in your TV can be located at several sections. Whithout knowing the exact section we can't answer you. Specify the section at least.
Ok.