20 Most Recent Panasonic PT-50LC13 50" Rear Projection HDTV - Page 9 Questions & Answers


Click here to download the insturctions on how to reset the lamp timer after lamp replacement.

Panasonic... | Answered on Jun 27, 2010


The projection lamp life are over.Require a new projection lamp for the replacement.

Panasonic... | Answered on Jun 23, 2010


Here is a link to replacing the lamp and the instructions for resetting the timer.
Just search for your set on the page.

I hope that this helps you.
asnowman

http://911phone.net/Panasonic_TY-LA1000_Instruction_Manual%5B2%5D.pdf

Panasonic... | Answered on Jun 21, 2010


that should be in the owners manual
techman
most sets havev a small door thathas has a screw on it and the bulb is inside a small cage you pull out
techman

Panasonic... | Answered on Jun 13, 2010


If it is a new bulb and does not come right on you need to take the platis housing off of the old bulb and put the new bulb in the old housing, the new bulbs dont always fit just right

Panasonic... | Answered on Jun 08, 2010


Make sure the Lamp Fan is running if it stops cooling Lamp or is not running Lamp will not Light.

Panasonic... | Answered on Jun 07, 2010


Hi,
Below image shows original TY-LA1000 lamp that comes in its housing.
Image-1
5c9a197.jpg


And this image shows bulb of TY-LA1000 lamp that many sites/ stores offer on less price.
Image-2
1392f91.jpg

Let me know did you received lamp or bulb as replacement to help you out accordingly.
Thanks.


Panasonic... | Answered on May 31, 2010


Defective light engine.

Panasonic... | Answered on May 28, 2010


Hi,
Below three images shows how to get access to lamp cover and lamp inside in Panasonic PT-50LC13 dlp tv.

1- Remove lower front cover.
a866200.jpg
2- You will see Lamp Cover there.
455c851.jpg
e093c91.jpg
Tight screws as shown in above image.
Hope this will help you.
Thanks.

Panasonic... | Answered on May 27, 2010


If you don't have the manual handy you can download it here.
http://service.us.panasonic.com/OPERMANPDF/PT50LC13.PDF
But I did not find it much helps as all you need is a TY-LA1000 lamp that can be purchased from a number of dealers on the internet, or you may have a shop locally that will sell you one.
I have even found them as cheap as $124.00 on Amazon.com.

The replacment instructions will come with the new lamp and also how to reset the lamp timer.
But here is a link to the lamp instructions.
http://www.fixyourdlp.com/wp-content/uploads/2007/09/panasonic-tyla1000-lamp-instructions.pdf


I hope this information allows you to resolve this issue.
I am doing this for free.
If I have helped you, please help me, and rate this suggestion.
If you need further assistance please comment to this post and I will try to help you further.

Thanks for using FixYa
asnowman


Panasonic... | Answered on May 07, 2010


1 turn tv on

2 press vol- on tv and pip on remote at the same time for more than 5 sec a message will appear

Panasonic... | Answered on May 06, 2010


The power supply will need to be repaired by a service center.

Panasonic... | Answered on May 06, 2010


you can simply go to the tv sets menu and go to lamp hours and highlight it then highlight reset and press enter

Panasonic... | Answered on May 04, 2010


Snap-off lower front panel ( about 4" tall x width of TV.) Door behind there with philips screw. Philips screw for lamp itself.

Panasonic... | Answered on May 02, 2010


check to insure that your input signal is clean,(clean picture) most modern TV`s blank the video if it is deemed of poor quality, also if you are using a VCR and are viewing pirate copy tapes the VCR will output a varying video level output signal to deter pirating of movies, using a video stabilizer between your VCR and your video input may solve this problem for you, check with your user manual as to the light flashing condition in the diagnostic section this will indicate the fault you are experiencing good luck

Panasonic... | Answered on Apr 27, 2010


Hold VOL - on the TV then aim the remote at the TV (watch so that your arm doesn't block the remote signal and press PIP or the SPLIT button. Do this together for at least 5 second. I hope this helps, best wishes.

Panasonic... | Answered on Apr 27, 2010


It means just that. Clean your air filter but to get to it is a different story. I would highly recommend calling an authorized service center to do it.. While he's at it, inquire about getting a ballast kit installed.

Panasonic... | Answered on Apr 24, 2010


press pip or swap on the remote and volume down on tv for 5 sec at the same time

Panasonic... | Answered on Apr 22, 2010

Not finding what you are looking for?
Panasonic PT-50LC13 50" Rear Projection HDTV Logo

482 questions posted

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

Demonic-2011
Demonic-2011

Level 3 Expert

512 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Panasonic Televison & Video

  • Panasonic Televison & Video

Most Popular Question

worth fixing panasonic pt 50lc13 k rear

  • Televison & Video
Loading...