20 Most Recent
Panasonic PT-47WX53 47" Rear Projection HDTV - Page 2 Questions & Answers
PT-47WX52F with bad resistors at
R832 is a 8.2MEG 5% 3/4 watt resistor
R7060 & R7066 are both .27 ohm 5% 1watt resistors,
You can get the full set of panasonic resistors from
www.tvrepairworld.com under the Panasonic repair kits its listed as the PT47WXC43 Resistor Kit that kit also fits the WX52 and WX42 models panasonics.
4/18/2013 2:49:23 PM •
Panasonic...
•
Answered
on Apr 18, 2013
Why does tv turn itself off
the cause is either a bad component in the power supply unit or if the lamp has a problem which cause an error detected by the main board.
4/15/2013 7:42:52 AM •
Panasonic...
•
Answered
on Apr 15, 2013
Panasonic PT-47WX54J - There are
Let me ask you an important question to resolve what I think your problem is:
Do you see a narrow band of light from top to bottom but no picture?
Does it take it a minute or so and is just to the right of center on the screen? It can be towards the far right---Is this what you are dealing with?
Respond by making a comment here or if you repost the question mark it in the title: ATTENTION SD TECH.
IF you have the problem I suspect you do it is a bad cap and I can tell you exactly how to get at it and replace it.
I am here to help.
REGARDS, SD TECH
3/24/2013 8:24:03 AM •
Panasonic...
•
Answered
on Mar 24, 2013
When i go to turn on the tv the red power light
BLINKING RED LIGHT IS ERROR CODE.
1. Unplug set for a few minutes.
2. Plug back in and turn on.
3. When red power light starts blinking--COUNT THE BLINKS.
4. THREE BLINKS, pause, THREE BLINKS (ETC) IS SHORT PROTECTION AND A DO IT YOURSELF repair for some people. I have complete instructions for this repair.
5. 5 blinks, pause and 5 blinks etc is short on 140 volt line and while not as easy as 3 blink error code it points to places to look at.
If this told you something you did not know, rate this solution as very helpful as I do this here for free.
Post a comment here when you know what error code is and I will help.
REGARDS, SD TECH
10/29/2012 4:46:58 PM •
Panasonic...
•
Answered
on Oct 29, 2012
Panasonic Pt-47wx53g no sound but has picture
A suggestion here--the fact you have sound is a good sign.This set was prone to one fairly simple problem----If you turn it on and after a minute or so (sound is there) you see a faint band of white or odd noise on the screen, usually to the middle or right side of the screen (hard to see) you have a bad cap and I can tell where it is and what its value is and how to get at it and replace it---less than a 5 dollar part--but you must let me know if you see the faint band top to bottom after a minute or two.SD TECHThis part is c509 and is marked on the board---it is a .47 microfarad cap at 200 or plus volts and many times the brown cap will have a crack in the side (not always) but if you have the band of noise it is the problem.There is right and wrong way to get at it to replace if if it is bad.
This is what the board (right side view and on right side as seen from rear of set looks like.)
10/16/2012 5:40:56 PM •
Panasonic...
•
Answered
on Oct 16, 2012
Colors are seperating
A very common issue on this set and others is called convergence---see attached pictures----if they look like your problem I can help.Here I can give you general information but on our Market Place I can provide you with step by step start to finish instructions which include every thing you will need and how to do the repair---typical parts cost will be under 30 dollars.Look at the photos and if any questions make a comment here.Regards, SD TECH
8/31/2012 11:04:01 PM •
Panasonic...
•
Answered
on Aug 31, 2012
Not finding what you are looking for?