20 Most Recent Mackie Tapco Th15a Thump Active Loudspeaker - Page 2 Questions & Answers

Hello, check if your Mackie, is with the latest Firmware update, you can get it on Mackie's official website I sent you the Mackie technical support link I hope you solve your concern Greetings Franco Dosil Hola, revisa si tu Mackie, esta con la ultima actualizacion de Firmware, puedes obtenerla en la pagina oficial de Mackie Te envio el link del soporte tecnico de Mackie Espero logres resolver tu inquietud Saludos Franco Dosil https://mackie.com/blog/support

Hello Abel, I sent you the link to download the service manual of the Mackie PROFX16 I hope you can solve the problem you have with your Mackie Greetings Franco Dosil Hola Abel, te envio el link para que descargues el manual de servicio de la Mackie PROFX16 Espero que puedas resolver el problema que tengas con tu Mackie Saludos Franco Dosil https://elektrotanya.com/mackie_profx16_profx22_sch.rar/download.html

Bypass the Effects by jumpering the EFX loop send/return jacks. Mine had a bad effects processor converter chip, that was random and lost main bus signal intermittently. arlingtonguitarshop-dot:com

Hi, the crackling noise means it needs a service, was it stored in a shed or garage ? As damp storage is the likely cause.

First thing to do is get a can of contact cleaner. Take off the knobs and spray it into the reostats below. Spray into all the switches and even into the sliders. Move everything back and forth - 0 to 10 (to clean them). If we're lucky, that will fix it. Good Luck

First, unless you are a trained or self-taught audio technician, don't attempt to repair the unit yourself. Let the professionals repair it. You can damage it beyond repair if you don't know what you're doing. Non-working channels are caused either by bad connections, bad solder joints or a dead IC op-amp. The causes of weak channels can be more challenging to track down. I'd suspect bad connections, dirty controls or connectors.

Glenn, Does it say 'overvoltage', or simply 'voltage'? For the clearest result brother, contact Mackie - 1-800-898-3211 is their tech line - they're super cool - I just always picture the guys at Mackie sitting around reading comic books and shooting guns into the air. good luck!

try aux out on channels 1-6

I think you mean No Lows, but if you don't have the solid lows your issue may be a blown sub speaker. check the large speaker with a direct signal if it does nothing that's your issue if it is working then your main amplifier board needs a check. with these separate components your best bet is finding the defective part, one of my Mackie's went silent once I replaced the speaker, Hope this helps.

You need 3.5 mm Stereo Jack to 2 RCA cable.

Are you sure the xlry cable is balanced? there are balanced and unbalanced xlrs. For phantom to work, you need a balanced xlr cable.

The "rude solo" wil only flash if something is soloed. You need to check again as there is STILL something soloed. The left meter is because that is showing the channel that is being soloed. Once you unsolo everything, the meters wil display full left and right as usual.

Hi, What you need to do is connect (for example" Aux 1 send from the desk to the Left Input of the alesis. Then connect the Left and right output form the Alesis to Auxilery return 1 and 2. You can just use the left ouput and use aux return 1 if having mono effects is ok.

I would take it to a Mackie authorized repair center. Service Locator Mackie

Possibly> It will depend on exactly where you're traveling to. Contact Mackie customer service to see if the transformer is tap-able to different voltages. Contact Support Mackie

It's probably not getting power to the lamp connector. Get a voltmeter and check it.

These must be one of the most fault prone speakers ever made. Disconnect the power supply from the amp and see if you can get it working then connect it back up but don't hold your breath, they regularly fail taking out the output stage which in turn takes out the PSU so check the amp with a limited and robust PSU or use a variac on the mains to test.

ALL the lights? Major fault, suspect not really ALL. please detail which.

Take the main outputs into a stereo input (or a pair of mono inputs) on the Peavey - without knowing which Peavey I cannot tell you further info re set-up but as you'll be sending line level signal you'll need to back off the gain on the channels you input to on the Peavey

That popping is a defective solid state device on the circuit board.