20 Most Recent
Kenwood KDC-MP228 CD Player - Page 6 Questions & Answers
I install a radio it dont keep a memory
Pull the radio back out. I bet you hooked up both power wires (red and orange or yellow) to the ignition on hot wire. Orange or yellow depending on the radio usualy goes to the ignition on hot wire and red to a constant hot wire. Check the radio wiring diagram or list. One of the power wires has to go to a full time power source. check the wires with a circuit tester with the key off till you find the constant hot wire (battery power)
1/17/2010 12:49:45 AM •
Kenwood...
•
Answered
on Jan 17, 2010
I needs code for cd player with no remote kenwood mp228
A remote has nothing to do with it if it isnt stolen take it back to where you purchased it or call poineer with receit if its stolen ill explain how to jailbreak it for 10 bucks crime pays me i guess and your the thief lol
1/15/2010 2:40:47 PM •
Kenwood...
•
Answered
on Jan 15, 2010
Can not set clock on Kenwood KDC228 CD Receiver
I spent the better part of an hour trying to figure out how to get the "Clk Adj" screen on the KDC-MP228. Here is the solution (dont waste your time reading the manual, it does not explain this). First, I had screwed up my settings so I did a factory reset (hold in the reset button). Then, you need to turn off Demo Mode (in standby click the Menu button and then use the control button to navigate to "Demo On". Hold the control button in to turn Demo on or off (this is different from all of the other controls in the manual). Now that Demo is off, click Menu button again and use the Control button to navigate through the options, one of which is "Clk Adj". At that point, you can follow the instructions in the manual (Hold in Control button until the clock blinks (approx 2 seconds), then use the FM/AM buttons to change the Hours and the << >> buttons to change the Minutes). Press the Control button again to save your changes. I cannot believe how difficult it was to set the clock on this device, someone should smack the developer who wrote that code.
12/20/2009 6:52:03 PM •
Kenwood...
•
Answered
on Dec 20, 2009
Unlock code
Hi there,
Click here for Robotek's Tip on unlocking Kenwoods.
I normally ignore problems that have more than two syllables, but in this case I made an exception. For breaking my own rules, I fully expect a four thumb rating.
Best regards
Mike
11/11/2009 3:11:19 AM •
Kenwood...
•
Answered
on Nov 11, 2009
Unlocking my Kenwood KDC7016
LOOK FOR RESET BUTTON, OR UNPLUG THE LUG FROM THE POWER(12V) AND REPLUG IT, ...OR IF ANY CMOS BATTERY IS FOUND INSIDE, MOVE IT AND REPLACE IT...HOPE IT WORKS
10/14/2009 9:10:42 AM •
Kenwood...
•
Answered
on Oct 14, 2009
New speakers are fuzzy
If it is an older vehicle you could have interference from the ignition system. You can wire the radio to be powered up from a toggle switch that get its power straight from the battery, with a fuse between the battery and switch of course. This will eliminate powering up the radio with the ignition switch and take the ignition system out of it. Also need to make sure the ground wire is grounded good and the ground wire is the same wire guage if not larger than the power wire.
9/28/2009 6:41:04 AM •
Kenwood...
•
Answered
on Sep 28, 2009
Kdc-mp228
It will have to be sent in to Kenwood.
9/8/2009 6:20:16 AM •
Kenwood...
•
Answered
on Sep 08, 2009
Unlocking code
The only CLARION code available for free (using a serial number ) from anywhere on the Internet is if your radio also has a BARCODE SERIAL NUMBER beginning with C7000000 + + + + on a label somewhere on the metal casing.
(There are usually two barcodes on one label. The one required is the lower one )
If not then it will only be available from your Main Dealer or a Decoding
9/6/2009 7:58:32 PM •
Kenwood...
•
Answered
on Sep 06, 2009
Not finding what you are looking for?