20 Most Recent
Zebra Z4M Printer - Page 7 Questions & Answers
Paper out error message
Recalibrate the printer via the Menu system, if this doesn't work you might have a faulty paper out sensor. Another thing to check that there is no old labels stuck on the upper side, this means label gum etc as the sensor is reflective.
10/29/2009 7:06:56 AM •
Zebra Z4M...
•
Answered
on Oct 29, 2009
Prints larger that print preview shows...
Firstly make sure your using the correct drive ZM400 rather than Z4M. if you are using the applications driver make sure of headers and footers sizes and the print area is set correctly. If your using odd sized lables download some new drivers from the Nice Label website, they are far more adjustable that the standard Zebra drivers.
10/29/2009 7:04:19 AM •
Zebra Z4M...
•
Answered
on Oct 29, 2009
Pause between each label.
When you go to file and print the dialogue box comes up and you inptut the amount of copies required, uncheck the Colate box just under the amount of copies required. This will allow each print to come out streamed no paused.
10/29/2009 7:00:02 AM •
Zebra Z4M...
•
Answered
on Oct 29, 2009
My Zebra 4M Plus displays (ribbon out)
If you don't use a ribbon, you are using it in Direct Thermal mode. You need to set your driver to use Direct Thermal rather than Thermal Transfer, this is in the settings under Media.
10/29/2009 6:54:25 AM •
Zebra Z4M...
•
Answered
on Oct 29, 2009
I HAVE RIBBON OUT ERROR WHEN THERE IS CLEARLY A
Enter the Menu system on the front panel, cycle around until you find calibration. Press the select button here and follow the instructions, when it asks for you remove ribbon remove it, it will ask to load the backing. Remove a label from the backing and let it do its thing, eventually it will ask you to load all. Re-install all the media and it will calibrate, after this it will fix your error. If it doesn't there will be a sensor that has failed.
10/29/2009 6:50:18 AM •
Zebra Z4M...
•
Answered
on Oct 29, 2009
Zebra Z4M, how do you remove the main logic board?
Open the side cover, locate the hinge screws at the top inside the cover. 4 remove the side cover and the others remove the other side cover remove the all it is easier that way, check the back to see if there are 2 more screws in the cover. Lift the cover upwards to expose the Main Logic Board, from here you should be able to work out how to remove the Main Board. There are 2 black holders on the main PCB don't open the as they can obtain the Flash RAM, they are very sensitive and if you touch them they can blow.
10/29/2009 6:39:34 AM •
Zebra Z4M...
•
Answered
on Oct 29, 2009
I have a Zebra Z4M printer. Just put new roll of
This is a calibration issue. The labels or ribbon are not loaded correctly. If they are, turn the printer off and then back on and the printer will run a calibrate. This should correct it. Once it is complete, you can verify by pressing the feed button and making sure it feeds one label at a time.
10/27/2009 5:20:38 PM •
Zebra Z4M...
•
Answered
on Oct 27, 2009
Made some noises. Turned off/on. Unplug.
Hello,
You have a bad main logic bd, this is a common problem with the units and your logic bd needs to be replaced or fixed. If insturctions are needed on how to remove the logic bd please let me know i can pot something up for you.
I also can repair or replace your logic bd if needed.
Rory Cardenas
708-597-4222 x240
10/23/2009 2:14:02 PM •
Zebra Z4M...
•
Answered
on Oct 23, 2009
Printer does not come ready. power, pause and
Hello,
This is a very common problem with the units, your logic bd is bad and needs to be replaced or fixed. If instructions are needed on how to remove the logic bd please let me know I can post something up for you. I also carry the logic bds in stock if needed or I can repair them as well. Please contact me back if you have any other questions.
Thanks
Rory Cardenas
708-597-4222 x240
10/22/2009 3:23:01 PM •
Zebra Z4M...
•
Answered
on Oct 22, 2009
Error light and pause light up instantly and never
Hello,
You have a bad main logic board and it needs to be replaced of fixed. If instructions are needed on how to remove the logic bd from the machine please let me now. I can post something up for you. If you are in need of a logic bd please contact me. I carry logic bds in stock and can further assist you.
Thanks,
Rory Cardenas
708-597-4222
10/22/2009 3:16:00 PM •
Zebra Z4M...
•
Answered
on Oct 22, 2009
We are printing PHarmacy labels....what
Hi,
If you want to change the template, you can do this while print previewing it on the computer. Just invert it, go to print properties. You would be able to do it from there.
Regards
10/13/2009 10:18:15 PM •
Zebra Z4M...
•
Answered
on Oct 13, 2009
Zebra 4M Plus
What software are using? If you use or Zebra Designer Label Matrix, uses its own drivers. If you use another driver, verify that the graphics option is "dithering".
Roberto Martinez
10/6/2009 4:41:59 AM •
Zebra Z4M...
•
Answered
on Oct 06, 2009
Slow Printing on Zebra Z4M
An unorthodox solution is to install an old driver. Another solution is to use with Codesoft the driver from www.seagullscientific.com, and with Zebra Designer, the Zebra Designer driver. If the printer is connected to the serial port, speeds up communication.
Roberto Martinez
10/6/2009 4:08:22 AM •
Zebra Z4M...
•
Answered
on Oct 06, 2009
I can not print an image on a Zebra Z4M
Sometimes when a picture or a field is partially off the label, this is truncated or not printed, try to move the position of the image.
Roberto Martinez
10/6/2009 4:01:11 AM •
Zebra Z4M...
•
Answered
on Oct 06, 2009
Not finding what you are looking for?