Symbol MC50 Pocket PC - Answered Questions & Fixed issues
Align screen thats all it says
Cold boot the scanner with the three finger contortion. Power Button, right scan button and the reset button at the same time. Wait for it to reboot. If it doesn't reboot, you haven't done it right. Redo it. Then if it comes up and keeps saying align you may have to hit the reset only button and wait for it to warm boot.
5/17/2011 9:47:51 PM •
Symbol MC50...
•
Answered
on May 17, 2011
•
570 views
I have 2 units of MC50, I connect to my WiFi ,
Based on the Information you have provided we can assume that either,
- You need to update your firmware and/or browser through the included update software
- Both units have been damaged in different ways, most likely the memory as browsers on pocket PCs are notorious for freezing like this when they run out of memory.
dIf updating the software on your phones does not work you will have to bring them in to a specialist to hto see which of the internal parts has been damaged.
3/15/2011 8:48:18 PM •
Symbol MC50...
•
Answered
on Mar 15, 2011
•
223 views
Cannot turn off flight mode
Cannot turn off flight mode on an MC50 so it will not transmit to my wireless network
Ekse: I see your having issues with your Symbol MC50 pocket pc / phone? the flightmode is stuck on?
Ekse: are you there?
Ekse: I guess you are not there but I think I can solve this problem and hopefully you will see my comments at some point
Read more Ekse: First you should try performing a normal reset
Ekse: there is the small reset button on the back of the unit. perform the normal reset and see if the problem persists
Ekse: if the problem persists back up any data from the phone to your computer, and then perform a hard reset, Howl down the power and right scan buttons, then press and release the reset, and then let go of the power and right scan buttons.
Ekse: the hard reset wipes the handheld and returns it to factory defaults, you will be online after the hard reset. then just restore your data from your desktop computer and your good to go.
Ekse: if you need further assistance you can reach me on email - or on the website.
7/24/2012 6:23:47 PM •
Symbol MC50...
•
Answered
on Jul 24, 2012
•
2,976 views
How do I restart my
There is a reset button on the back, bottom right hand side of the device. This could be pressed using the stylus
1/28/2011 6:17:20 AM •
Symbol MC50...
•
Answered
on Jan 28, 2011
•
346 views
How do you silence the beeper?
Start --> programs --> File Explorer --> Windows --> CtlPanel --> Scanner Settings --> Scan Params --> Change Wav file and Start Wav file to some other sound. Thats the only way i've found to quiet it down.
1/24/2011 8:31:07 PM •
Symbol MC50...
•
Answered
on Jan 24, 2011
•
234 views
I have three pocket pc--symbol
in settings go to wireless manager and turn wlan on.in some phone there is a quick acess key on the side for this.
please post comment
12/23/2010 2:47:13 AM •
Symbol MC50...
•
Answered
on Dec 23, 2010
•
362 views
I can not get Symbol MC5040 to connect to the
Hello,
What you need to do is to carefully down load the symbol fron the internet with another computer system then copy it with a flash drive on make use of USB cord to transfer the symbol to your MC pocket PC so as to able to load in to the net this recommendation is for USB cord .
If you like to make use of flash drive, after down loading the symbol from the net plug in your flash in to the PC you are making use of copy it from MY COMPUTER in to the flash , then remove the drive carefully the install it to your pocket pc through the USE pot open it and then up load it.
Good luck.
Thanks.
12/12/2010 3:19:41 PM •
Symbol MC50...
•
Answered
on Dec 12, 2010
•
185 views
I have a Symbol MC50
Welcome to Fixya
Routers has DHCP capability which enables them to provide IP address to computers and this is automatic unless you set the the router to manual. Inorder for you to verify this capability, you need to connect a computer to the router and go to command prompt of the computer and type ipconfig. If you are not getting any IP address then the problem is the router.
Please get back to me for any update.
Thank you for using Fixya! If you need further help, reach me via phone at
https://www.6ya.com/expert/elixirjose_00375ea24bd8141b
12/14/2010 12:24:41 AM •
Symbol MC50...
•
Answered
on Dec 14, 2010
•
575 views
My symbol mc50 scanner wont
Hello,
it is possible that if you changed the battery you forfot to move the slide button next to the battery to the correct position. It often happens to me :-) Please check it, its on the right top corner of the battery, you should not see the red marking, if there is the correct position.
12/2/2010 8:42:12 AM •
Symbol MC50...
•
Answered
on Dec 02, 2010
•
1,563 views
I have a Symbol MC50
If the scanwedge program is loaded and enabled, your scan engine is bad. Check to see if scanwedge is running and scanning is enabled
10/13/2010 3:54:50 PM •
Symbol MC50...
•
Answered
on Oct 13, 2010
•
384 views
HOW TO RESTORE FACTORY DEFAULT
There is a program you can download from symbol/motorola and place on a sd card and follow the instructions with the card and program. Otherwise send it to me and I will do it for $100.00.
10/13/2010 3:50:02 PM •
Symbol MC50...
•
Answered
on Oct 13, 2010
•
1,036 views
I purchased a Symbol MC50 MC5040 WIFI Bar Code
All MC50s are equipped with an scanner, if you would read out the Full Product number (like MC5040-XXXXXXXXX) of your device. Then can you check which kind of scnner is built in. The Software is usually preinstalled in the /Application folder.
10/7/2010 8:02:47 PM •
Symbol MC50...
•
Answered
on Oct 07, 2010
•
502 views
Not finding what you are looking for?