Top 20 Ricoh Aficio 1515MF All-In-One Laser Printer - Page 6 Questions & Answers

You need to tell the machine it has a delivery server, this can be done by selecting user tools/system settings/file transfer/delivery option/On. After doing this you may have to remove and readd the I/O device from within scanrouter.

Press the printer button, it will tell you on the screen what the problem is. Generally it is because your computer is telling the printer that it wants to print on a size paper that you don't have loaded in the machine.

The 1515 is compatible to the 161 and the 171, the two newer generations of similar printers. All three use the same toner and photoconductor units, and are set up almost identically.

check and make sure cable in lower left side of door in in firmly

Press the [Printer] button and then the the button under it. It looks like an arrow pointing to the right. Look on the screen it will switch between offline and online/ready depending on the condition of the network.

use a high power air blower to clean the document feeder its exit sensor is dirty

please your copier fuser thermostator is displace or over dust toner clean it and solve your problem

this device does not support scan router v2 lite.
your best bet would be to set up using SMB scan to folder.
set up is pretty straight forward create a folder on the root of C: ie C:scans
share the folder with full permissions, simple file sharing has to be turned off!!
then go into the device web page using the IP address ie: 192.168.xxx.xxx.
go to configuration and smb create a user name ie: bill then point the device to the computer you created the folder on, ie: bill's pc/c:scans
save the configuration log out of the web utility reboot the device and you should have succesfully created an smb folder share.

if this resolves or answers your query please rate me accordingly
good luck and thanks

Found some information here:
http://www.fortc.com/2007/06/17/ricoh-cl4000dn-error-code-sc542/

Try the following

press the yellow “C” button
enter 107
press the red “C” button and keep it hold till the display changes
turn the power off with the big red switch on the front side
turn power on again.

OR

• Press and hold online + escape, then power on.
• Use up and down arrow keys to select SP2
• Press Enter
• Use up and down arror to locate SP5
• Press Enter
• Use up and down arrow keys to select 810
• Press Enter
• Confirm the selection
• Power off and on.

get tweezers and pull it all out, rotate roller and look for more paper. A scrap is still somewhere triggering that sensor to not let you print.

Folder must be fully shared, (full control for everyone.) create a user name and password that has admin priviledges. Enter this info in Config>File transfer>SMB.
Enter the path to the folder in the address book, in this manner> \\name of computer folder is on\name of directory\name of folder.

Go to this link and download any manual you want for that model, otherwise you can always download "IP SCANNER" , if the printer is connected on a Network, to determine the IP Address of the Printer!

Good luck, download the other manuals on the following link in order to change the IP settings on the Printer to what you want

http://www.ricoh-usa.com/downloads/manuals/bw/aficio1515/

You either have a defective thermostat (thermistor) in your fuser, or a defective power supply. The error can only be reset by a tech in service mode after the problem is fixed

ricoh dose not work through SLL

If you can print to it the network setup is ok. It sounds more like a print driver problem.

hi,
as long as copy quality is not a issue you can use it. If you order a photoconductor you can replace it by your self.
Regards

IF you replaced the entire PCU, make sure you pulled the plastic tabs from the unit and removed the protective paper from the drum area. I don't remember if the new PCU comes with developer pre-installed.
If you replaced the drum/developer, it is common for the lower developer unit drive gears to wear down and break off some of their teeth.

Hope this helps.

When you say startup, do you mean when you turn the machine on or when you attempt to print?

For the first, check to see if there isn't any small piece of paper stuck anywhere in the paper path. for the second condition, clean off the feed roller with a piece of cloth dampened with alcohol.

Its possable to print to a networked ricoh 1035 from a Mac... You need the Postscript option...

Go here :
http://www.ricoh-usa.com/downloads/downloads.asp?tsn=Ricoh-USA&path=http://support.ricoh.com/bb/html/dr_ut_e/rc2/model/x15_15f/x15_15fen.htm
You should be able to download the manual for free,