Ricoh Aficio 1515MF All-In-One Laser Printer - Answered Questions & Fixed issues

GoDaddy Customer Care Number

Red light all time when ink is finished and refilled it.

First download the twain drivers from Ricoh website or if you have cd down load it from it. Then from there when you go to scan should give you selection option for it.

Clean MBU interface. Clean with dev. Make sure you can see gold pins. Clean male adapter on MBU board with dev. Pic : SP201 ricoh MBU clean up with dev.

Could be one of a few things:

Most likely is the transfer roller. If it's dirty or old and not applying enough charge, it may not be pulling all the toner away from the drum. Replacing the transfer roller is easy if you can get a new one.

Are you sure you have the correct toner? The wrong toner can definitely cause copy quality problems.

If the springs that hold the press roller against the hot roller are not properly in place (or if they have started to lose tension) the toner won't be fully fused onto the paper.

I'd start with the transfer roller (black roller that sits opposite the drum on the right side door) first -- it's the most likely culprit.

Here is the link to Ricoh's website and the 1515 drivers. Just select your PC's operating system.
Good Luck and Thank You for using Fixya.
Please return and give me feedback on my solution.

http://www.ricoh-usa.com/downloads/downloads.asp?tsn=Ricoh-USA&path=http://support.ricoh.com/bb/html/dr_ut_e/rc2/model/x15_15f/x15_15fen.htm

press the orange key threee times and enter 107 and then press and hold the stop key for about five seconds. the machine then takes you into the sysytem. select sp mode on the screen. put off the machine for a minute and put on again

TD sensor is a electronic sensor that is short term from T-toner & D-density, so the Toner Density sensor is at is says Detects and measures how much and does have a toner in the developer unit.

To clear the memory (reboot) the RICOH AFICIO you will have to send it to the factory where they will wipe the memory and restore the machine to its defaults.

The photo conductor is the round drum unit that is light sensitive. The laser in the printer writes an image of what you want to print on the drum and then the toner is applied to the drum and transferred to the paper.

Laser, inkjet?

your machine is broken...buy a new one

542 Fusing temperature warm-up error (center) The fusing temperature rises less than 7 degrees in 2 seconds, and this continues 5 times consecutively. The fusing temperature is not detected in 25 or 35 seconds. • Fusing thermistor defective or out of position • Fusing lamp open • Power supply board defective This is the reason for the error code according to (printcopy.info) Might help you in some way, but not my area of expertise.

Hi there! As you have to understand, i (WE..) are subject to some secrecy about codes... its not because we enjoy it but , hey, we are dealing with juice. If all people has access to codes, 4 me its ok! NOTHING to worry about! Its what you make of them if you dont have a clue what you are dealing with... You wanna be the nice guy who solve a problem but you run away the net if you f** *** a bad situation so.. Heres is the access to service mode. But please, and this stand to ALL rookies, this is always goes in your responsibility, so be gentlly.Yellow button, 1, 0,7, and stop (red button)keep this button pressed by 3/4 seconds... YOU WILL SEE ACCESS TO TECH MODE.WHAT YOU WILL DO FOR NOW ON ITS IN YOUR INTIRE RESPONSIBILITY! I HAVE BEEN WORKING with ricoh and all machines related ( Rex Rotary, Nashuatec,Etc etc , and also Minolta, Toshiba,Canon, etc , you name it,ive seen them all,... and its about 30 years... but after all, as a tech man, i have to render to a status! Y ou have to had a training course, a problem or two,who made you familior with the machine, and so on ( Is 30 years!!!) and then you play with solutions.4get about newcomers, going to tech manuals and give you the answers already writen there...30 years working on this dont make me an expert, but..advising you not to take the short way...im serious! I Really enjoy Fixya! And, sometimes,i come here to get a second oppinion, when there is a doubt.so........

press clear mode then press 1 then press0 then press 7 then press stop button hold down for 5 seconds should see display say 1copy press 1 then press 7 ok then press 810 press ok follow instructions.

Go to admin settings
or using web browser u can change it

It's either 0000 or 1111

Check fuser roller gear. Hope it will helpful

you mail us [email protected] - we also suplly and fit pcu's

If you are using an LDAP server to provide the destination, you may not have the Search Conditions programmed correctly.