20 Most Recent Ricoh Aficio 2022 All-In-One Laser Printer - Page 8 Questions & Answers

if you found this functional problem SC542 then first of all you clear the all mode to press the clear mode button after this with in 30 second dail 107 from keypad after this press and hold the clear/stop button then it will show other thing you just press exit 2 time now shutdown the main power and again on it will ok now...

Please check the Toner supply unit.
If necessary dismantle it carefully and clean all the toner inside it and clean all the small parts. There must be 2 small mylars attached inside to the cover toner supply unit - If not there that's the problem.
Check also for broken parts.
Try replacing the whole toner supply unit.

Good luck and please rate me, thanks.

This is a problem with toner density sensor. It may need cleaning or replacing.

Here definition and eventual fixes:

SC392: TD sensor initial setting error
-Definition-
TD sensor output voltage falls out of the adjustment range (2.0 ± 0.2 V) after the
TD sensor initial setting has been finished.
- Possible causes -
• Someone forgot to remove the toner seal of the PCU
• ID sensor defective
• TD sensor abnormal
• Drum does not turn
• Development roller does not turn
• Poor connection of the PCU

Try disconnecting power cord and restarting the machine.

If you have a spare toner, test a different toner. A faulty cartridge may cause this same error.

If the problem is not cleared , then often this error is caused by a faulty drum. Since there are several different fault that can trigger TD sensor error, it would be better to have a technician testing the unit before replacing parts.

If you want to know part prices, or if you want a quote on repair, you can call Ricoh number listed on your owners manual.

Regards.

• Someone forgot to remove the toner
seal of the PCU
• ID sensor defective
• TD sensor abnormal
• Drum does not turn
• Development roller does not turn
• Poor connection of the PCU drum unit
Clean connector of TD sensor and
Try Change the development unit, adjust TD sensor.
Clean and you verify the connector of PCU.
Good luck...

Hi,
SC 392 Possible causes -
· Someone forgot to remove the toner seal of the PCU
· ID sensor defective
· TD sensor abnormal
· Drum does not turn
· Development roller does not turn
· Poor connection of the PCU
Regards,

Are you using ScanRouter or SMB (SMC?) ?
How are the others setup?
Does the laptop have connectivity to the machine (print,Webbrowser)

I've solved these poblems hundred of times

· Scanner home position sensor failure
· Defective scanner motor
· Defective main board
· Defective dc power supply board
· Incorrect scanner drive wire position
· FU202 on the dc power supply board open (blown fuse).
- Action -
Turn the main switch off and on.
Check the position of the 1st scanner sensor actuator.
Actuated De-actuated
Does the scanner motor rotate when the main switch is turned on?
No Yes
Correct the scanner drive wire position.
Check the voltage at CN106-2 on the main board.
24 volts 0 volts
Check FU202 on the dc power supply board.
Good No Good
Replace FU202
Replace the dc power supply board.
Check the voltage at CN105-1 and 6 on the main board.
24 volts 0 volts
Replace the main board.

Poor connection of the fuser, and the code will need to be reset in service mode.

change the photoconductor....

Call up a Ricoh sales representative.

Enter SP 5810 (SC code reset), select “Execute”, select “close”, exit SP mode then turn main power switch off and on.
to enter SP mode press yellow C button press 1 0 7 on numeric keypad and then hold down the orange C button from the menu select copier SP then type in 5801 and press # selest execute then power off and back on. Your machine should now be working. Hope this helps.

Try sending a test sheet using "hook" to a known good fax if it goes the fax is fine (it wont leave the doc feed till its coming out on the rx. fax.) If this works then maybe the speaker is bad or disconnected. As for the report you need to chance the transmission report to off or error.
-Carl, please let me know if this helps.

In the start menu click network,on the bar on top click network and sharing center,scroll down and enable network discovery.

Set a compatible IP address on machine:
"user tools"
"system settings"
"interface settings"
"IP address" (set compatible number)
"subnet mask" (set the right one)

Download driver if it's not done already, create the matching tcp/ip port, and continue with installation. Select "share this printer".

Driver is here if you need it:
http://www.ricoh-usa.com/downloads/downloads.asp?tsn=Ricoh-USA&path=http://support.ricoh.com/bb/html/dr_ut_e/rc2/model/x2022_27/x2022_27en.htm

That could be caused by a number of things:
Are you connected to the phone line by a very long telephone cable? This can cause extra interference and cause these codes. Or it could be a deteriorated cable...try another one.
otherwise, it could be a fax circuit board problem, but more likely you need to have the 'cable equalizer " adjustment performed in "service mode", which is a fairly simple adjustment for a service tech, but too complicated to explain here.

I hope this helps.

I ended up taking out the toner bottle completely and just running copies (with no toner in place) until they came out crisp. This used up the toner that was floating around. I was able to make about 700 copies before I needed to put the toner back in. But a **** of paper is still much cheaper than getting a service tech.

You'll need a tech on site for this one, but it may be difficult to source parts if required for this old box. One of the following situations has occured:

• Poor connection of CCD
harness
• Dirty optics
• Defective lamp regulator
• Defective main scanner IPU board
• Defective CCD

Hello sir; This error code is indicate video process error, may be can be reset, the procedure as follow;
press "clear mode", "107", then press and hold down "clear/stop" key for about 3 sec., until SP menu display, touch "copier sp" on screen, enter 581002 then press 1, then turn power off and back on. see what's happen. good luck !

Seems to me the serial number plate on those boxes was located by swinging out the toner bottle...just a guess.