20 Most Recent Lexmark X7170 All-In-One InkJet Printer - Page 4 Questions & Answers

Hello,
Please make sure that you have installed the correct drivers for your printer. Also, please mention the operating system you are using.

Lexmark haven't releaseddrivers for Vista or Win7 only available for Win XP 32bit I'm afraid :(

A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Disconnect the printer from your computer. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the everything turns back on, reconnect the printer into the computer. Wait for your computer to fully recognize the usb connection. Try to scan again.
You can also try to update your printer driver. Just insert the installation disc into the pc hard drive and run the setup application.

The error code 2200 indicates that the cartridge carrier has stalled or jammed. Please follow the steps found in this article in the Lexmark website about 2200 Error on the Lexmark X7100 Series All-In-One to fix the problem.

Hello.
Try this link below. the manuals are in PDF Format so a appropriate reader is needed.
http://www.fixya.com/support/p306866-lexmark_x7170_all_in_one_inkjet_printer/manual-19315
Regards GM

Most fax machines are set-up to pick up all calls. There isn't a way to know you are receiving a voice call until the fax picks up and doesn't hear the tracer signal that kills our human ears.

You could change the number of rings it takes the fax machine to pickup the call. If you set it to the max, you would have plenty of time to pick-up. this option is normally part of the settings on the machine itself.

The only other options are to unplug the fax when you aren't expecting to receive a message, or get a dedicated fax line. It depends on how much you use the fax.

Hope this helps! Please don't forget to rate the answer!

The roller has melted, replace the roller at authorized service center

What do you mean by "I'm trying to send a problem"?

Try to check if the cable is connected on both ends of the printer and the computer.

It could be that your right cartridge is not properly seated in the carrier. Open the printer and remove both cartridges. Close the cover. Unplug and replug the printer into the power source to reset it. When the printer turns on, reinsert both cartridges and make sure they are seated properly and securely. If error still appears, try to insert a different known working cartridge to determine if the other is faulty.

It could be a faulty cartridge. Have you already tried inserting a different known working cartridge? If error continues to pop-up even with a different new or a known working cartridge, then it could be a hardware problem. Try to contact Lexmark technical support on the phone for additional assistance.

If you still have the install disc for your printer, re-insert the disc in your hard driver to repair any corrupted Lexmark printer softwares. You may try the driver from the Lexmark website:
- X7170 driver for Vista 32-bit - X7170 driver for Vista 64-bit

Open the cover, and look carefully -- there is a small "sensor" that should be activated as you close the door. If the sensor is malfunctioning, then it never sends the "door-is-closed" signal to your computer. There might be some paper-dust that is interfering with the sensor.

You can download and install the Lexmark X7170 driver from the Lexmark website. Just click on this link: Lexmark X7170 Drivers

This article in the Lexmark website will help you identify and resolve the 1203 cartridge error problem: 1203 Error Message on the Lexmark X7170 All-In-One

Please go through the following checklist found in this article: The Printer is Not Powering On. If problem continues, please contact Lexmark technical support for additional assistance.

You can get the drivers/software for the printer on the link below. You will need the software to work the printer.

http://support.lexmark.com/index?locale=EN&page=product&userlocale=EN_US&productCode=LEXMARK_X7170&focusedTab=DOWNLOADS#2

The error indicates the has stalled or jammed. This article in the Lexmark website on 2200 Error on the Lexmark X7100 Series All-In-One might help fix the problem.

Wiping the nozzles with a moistened soft cloth or removing and reinserting the cartridges usually helps. The cartridges for the Lexmark X7170 are black: 32/34 and color: 33/35. If these are the cartridges that you purchased and even tried your old and new cartridges yet the problem persists, please don't hesitate to contact Lexmark technical support.

sometimes you can't see the paper jam, it may be a small peice of paper that tore off a page while going through, you need to take the top and back off the case and look closely at the rollers to see if there is something in there.