Pitco Frialator SG14 Deep Fryer - Answered Questions & Fixed issues


Hi there,
Fryer's Digital Controller will display "BOIL" if the temperature is it reading does not exceed 212F or 100C for quite some time. Make sure that there is enough level of oil (not water) in the Fry Pot before turning it on.

Pitco Frialator... | Answered on Apr 29, 2017 | 267 views


Sounds like propane. Please is heavier than air. Try opening air shutters on burners.

Pitco Frialator... | Answered on Dec 04, 2016 | 381 views


Sounds like thermostat or no fuel. Gas lines on? Correct orifice for the type of gas youre using?

Pitco Frialator... | Answered on Jun 13, 2016 | 454 views


call a good gas repairman sounds like your pressure regulator might be bad .

Pitco Frialator... | Answered on Nov 06, 2015 | 194 views


loose thermocouple connection at valve.

Pitco Frialator... | Answered on Jul 17, 2014 | 828 views


Replace the thermophile

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Pitco Frialator... | Answered on Jul 16, 2014 | 407 views


first be sure the valve is in the on position. sounds crazy but I've been there. Next even though the pilot is lit it may not be burning hot enough to make the Thermo pile produce the 750 millivolts the valve needs to operate. If the thermo pile is producing the proper current then the gas valve itself is the culprit. If you are not comfortable with gas and do have the proper testers You should call a pro. The pilot is easy to clean though. turn the gas valve to the off position and remove the pilot. When you remove the gas line to the pilot there is a small oriface inside that looks like a little thimble. Remove it and clean it. the gas flows through a very small hole that clogs very easy. Reassmble it tighten the gas line. Check for leaks with some bubbles and give it a try.

Pitco Frialator... | Answered on Jun 06, 2014 | 116 views


Sounds crazy but check for power at the outlet. If that's good then possibly a bad cord,Power switch or interlock safety switch if it has one. Do you hear a humming sound when you try to use it? If so the motor is frozen up. Hope this helps.

Pitco Frialator... | Answered on May 25, 2014 | 88 views


I am not familiar with this unit but I would highly recommend you get a service tec, it sounds like the gas pressure is to high and this would be an extreme fire hazard. I would highly recommend not using it until it is repaired.

Pitco Frialator... | Answered on Apr 29, 2014 | 98 views


Hi I use to repair every kind of restaurant equipment under the sun..maybe I can help...Is this a new install of the fryer and it never did this before, or did this just start do this..If a new install, the first thing I would check is the gas regulator and see if it is for Nat gas or Lp gas, and find that out..cause it has to match what you have, comming into the building..usuall the gas valve has a sticker on it that says what the water columbs are like for Nat it is like 3-6, and for Lp(propane) it is like 5-12. Ive seen customers buy a used fryer, and install a LP fryer in a Natural gas build, and the valve lets too much gas to the burners, and it will shoot flames out the top..then you would have to buy and convert a gas valve, or use parts to convert it..let me know further..

Pitco Frialator... | Answered on Apr 20, 2014 | 160 views


THE POWDER HELPS TO COLLECT THE PARTICLES IN THE GREASE TO HELP IT SINK TO THE BOTTOM OF THE FLITER SYSTEM FOR EASIER REMOVALE

Pitco Frialator... | Answered on Feb 20, 2014 | 97 views


Hi there.
Check first if there are no foreign objects hangings on the ball causing leak.
If you really need to change the ball valve, cling the jaw of a 14-inch pipe wrench on the neck of the valve connected to the fryer drain and turn it counter clockwise (***do this with no oil on fry tank and make sure that the tank is cold).
Wrap a teflon tape on the thread before installing the new ball valve.
Regards.

Pitco Frialator... | Answered on Nov 22, 2013 | 230 views


Check if there is no foreign object jammed on the ball valve. You must first drain the oil. Examine also the gasket for damage, if there is, you have to replace the ball valve.

Pitco Frialator... | Answered on Jul 21, 2013 | 296 views


You need to identify where the leak is coming.
If the leak is on the fry tank, best way to address it is to replace the oil tank.
Check the serial number of the unit with leak on fry tank, verify if it is still under warranty at PITCO web on http://www.middleby.com.

Pitco Frialator... | Answered on Jul 21, 2013 | 1,131 views


Visit http://www.middleby.com and go to PITCO web, you can download there installation, operation and user's manual which you can use as reference.

Pitco Frialator... | Answered on May 03, 2013 | 152 views


If you didn't figure it out already you lost the orifice on the pilot light. It's a little metal cup with a tiny hole in it that slips over the end of the gas tube in the pilot assembly. The orifice controls the size of the pilot light. Need to get a new one or find the lost part.

Pitco Frialator... | Answered on Oct 21, 2012 | 408 views


If you have build up of soot you need a service and a gas fitter to do it .

Pitco Frialator... | Answered on May 15, 2014 | 359 views

Not finding what you are looking for?
Pitco Frialator SG14 Deep Fryer Logo

Popular Tags

242 questions posted

Ask a Question

Usually answered in minutes!

Top Pitco Frialator Kitchen Appliances - Others Experts

Paul Carew

Level 3 Expert

3480 Answers

Treefrog15
Treefrog15

Level 2 Expert

130 Answers

Joe Palazola

Level 2 Expert

124 Answers

Are you a Pitco Frialator Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...