Top 20 Kyocera Mita Mita Copier Toner Cartridge for Mita KM-1525, 1530, 2030 - Black Questions & Answers

A J10 shows up if there is no feed from the upper paper tray. Check the operation of the paper feed clutch for the upper drawer. Good luck, Peter

Question edited to better English and spelling. Question moved to Kyocera MITA. https://www.google.com/search?q=Kyocera+Mita%2C+replaced+toner+but+still+says+replace+toner ..

https://www.manualslib.com/manual/359935/Kyocera-Km-2530.html?page=1#manual https://www.manualslib.com/manual/359935/Kyocera-Km-2530.html?page=10#manual https://www.manualslib.com/manual/359935/Kyocera-Km-2530.html?page=11#manual

Question edited for a lot more clarity!! Question moved to make model category. No you have to fix it. You need a service call.

KM-3050 KM-4050 KM-5050

moroinformatica.it http://www.moroinformatica.it > docs > KYOCE PDF Apr 1, 2013 - KM-4050. KM-5050 ... (4) How to tell a genuine Kyocera Mita toner container ... F14F. Power source PWB secondary side error. Defective power. 455 pages

Hi, Check the power saving setting under the printer. Usually the power saving setting for network is switched on, this needs to be switched off.

motor y sustituir la cinta de transferencia

You don't need to shake the toner. You only need to shake the toner when you install a new one. Shaking the toner to make it last later can give the copier a false toner reading.

You don't . OEM toner works best.

Press and hold the following buttons in the sequence below. (1) Stop/clear, (2) start, (3) exposure lighter, (4) exposure darker, release the 4 buttons and press the stop/clear button again. the display should now indicate 000. below the display are 3 buttons... press the left button once, the middle button 6 times, and the button on the right 3 times. the display should now indicate 163.... press the start button 3 times. your machine will now restart, and if the code was as a result of a power problem, should now work fine. if not the problem could be related to the fixing unit, power supply, or one of the boards. Also do not tamper with any settings while in the service mode, this WILL have undesired effects. TAKE NOTE, this will only work if your model is the KM-1500

press and hold the following buttons in the sequence below. (1) Stop/clear, (2) start, (3) exposure lighter, (4) exposure darker, release the 4 buttons and press the stop/clear button again. the display should now indicate 000. below the display are 3 buttons... press the left button once, the middle button 6 times, and the button on the right 3 times. the display should now indicate 163.... press the start button 3 times. your machine will now restart, and if the code was as a result of a power problem, should now work fine. if not the problem could be related to the fixing unit, power supply, or one of the boards. Also do not tamper with any settings while in the service mode, this WILL have undesired effects. TAKE NOTE, this will only work if your model is the KM-1500

http://www.koceramitaofficeequipment.com/

IF SOME KEYS NOT WORKING THAT MEAN YOU HAVE TO BLOW THE KEYS FIRST . MAY BE SOME KEYS ARE STUCK . IF THAT DOES NOT WORK I AM AFRAIED YOU HAVE TO OPEN THE KEYS PANNEL MAYBE ONE PRESS ELEMENT OR MORE ARE DAMEGED.IF SO YOU HAVE TO REPLACE IT.

IF YOU MEAN THESYSTEM MENUE PRESS 1087 TWICE.

http://www.manualslib.com/manual/288946/Kyocera-Km-2050.html?page=65 or https://www.manualowl.com/m/Kyocera/KM-2050/Manual/166911

Hi You need to check that the paper detection sensor just close to the rollers is still there , you might have blown it out of place or worse broke it , that's the only sensor that detects the paper

On which machine?

Firmware is not available on line! That is property of the company they only give out o authorized dealerships and corp techs, you will need a tech to re-flash the firmware. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

If you go to kmaconnect and read, there is a fix for that problem.

The cleaning lamp (which is in the drum unit) is defective. Replace the drum unit.