20 Most Recent
Toshiba E-studio 2330c 2830c Color Multifunction Copier - Page 4 Questions & Answers
How to fix toshiba photo copy machine not printing black and white but printing color and the black toner is full
If your Toshiba photocopier is not printing in black and white but is printing in color, there are a few possible causes and solutions to try. Here are a few things you can try:
- Make sure the machine is set to print in black and white. Some photocopiers have a setting that allows you to choose between color and black and white printing. Check the settings on your machine to make sure it is set to print in black and white.
- Check the toner cartridges. If the black toner cartridge is full but the machine is still not printing in black and white, there may be a problem with the cartridge. Try removing the cartridge and shaking it gently to redistribute the toner inside. Then, clean the contacts on the cartridge and the machine to ensure they are making good contact.
- Check the fuser unit. The fuser unit is responsible for heating and fusing the toner onto the paper. If the fuser unit is not working properly, it can cause the machine to not print in black and white. Check the fuser unit for any damage or debris, and clean it if necessary.
- Check for any error messages. If your machine is displaying any error messages, try to troubleshoot the problem based on the specific error message. You may be able to find the meaning of the error message and a solution in the user manual for your machine.
- If none of these solutions work, you may need to contact Toshiba for technical support or service. They may be able to help you diagnose and fix the problem with your machine.
Toshiba e studio 167 cannot use this size error how to fix it
Hi,
please power cycle your device and attempt to move forward. If error still persists, please alter the size of your paper to one that's appropriate for the printer or change the settings of the printer to allow for the paper size.
This would require you to reference the table of contents in the printer manual to follow the paper-size setup steps.
Thank you.
Toshiba 255 photocopier is powering off while running?
Hi,
Please double check that the printer isn't overheating because this might be a safety function activating due to high temperature. If this is the case, please lower the temperature from the a/c control in the room.
Also, please swap power outlets to rule out the first socket that you're using.
Thank you.
Reset Toshiba Estudio3055c
1. Turn the power of the equipment OFF and check the
connection of the HDD.
- Connector and harness check
- Check if the connector pins of the HDD are bent.
- Check if HDD for other equipment is not installed.
- Check if SRAM for other equipment is not installed.
2. If the error still occurs after step 1, perform the following.
- Perform HS-73 Firmware Assist mode -> Key
Backup/Restore and check that each Key Status is
"OK".
- If not, recover the key (copy "SRAM Key Status" to
"FROM Key Status" or vice versa).
3. If the error still persists after step 2, perform the
following.
- Perform HS-73 Firmware Assist mode -> Format
HDD, and then install "System software" (HS-49
Firmware Update mode -> SYSTEM SOFTWARE
(HD Data)).
Notes:
The following items will be deleted by HS-73
Firmware Assist mode -> Format HDD.
• Message Log
• Job Log
• Spool Data (Print, Email reception)
• Template
If F101_1 occurs with secure HDD or the error
persists after performing step 3, perform step 3 after
performing HS-74 HDD Assist mode -> Revert
Factory Initial Status HDD.
4. If the error persists even after step 3, replace the HDD.
5. If the error persists even after step 4, replace the HDD
harness.
6. If the error persists even after step 5, replace the SYS
How to fix a toshiba BARCODE Printer ribbon take up roller
Hi,
Are you referring to the platen roller? The platen roller is the cylinder that's underneath the printhead which pulls the labels from the roll/box and then pushes it at a certain speed so that the printhead prints onto the label. The platen roller is usually coated in rubber and you can check if the platen roller has some eroded or cut sections.
Unfortunately, the platen roller is a consumable item, you'll need to replace the platen roller. Take a look at our blog for more information about the platen roller.
https://www.bartechsystems.com/barcode-printer-not-working/
Not finding what you are looking for?