20 Most Recent Canon MultiPASS F60 All-In-One InkJet Printer - Page 3 Questions & Answers

http://www.driverrepairs.com/canon.php

First, you should check the manual to see if it says anything about this condition. If not, or you lack a manual, open the cover. The print heads will probably move to the middle so you can access the cartridges. Watch what direction it came from. If you look over on that side you'll see the parking area. The waste ink reservoir is below the parking area or may be on a moving parking mechanism. You may be able to pull it out or just get it with some paper towels. There might be a special door or procedure for emptying the waste ink receptacle.

SOLUTION 1
On the operator panel, press and hold the <ON/OFF> button for one second. (The display will go blank.)
Note: It may be necessary to unplug the power cord if pressing the ON/OFF button does not shut off the printer.
Wait approximately ten seconds and then press the <ON/OFF> button again.
Wait until the device has completed its cycling process before submitting another job request.

SOLUTION 2

• Enter the Service Menu (By Pressing Menu - Copy - #)
• Select Test Mode
• Select 8 [PRINTER TEST] in Test Mode.
• Select 3 [EEPROM Clear]
• Select 0 [INK COUNT]
• Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.
• Now I'll advise you here to call Canon 1-800-828-4040, and inform them that you have reset the counter, but you needed to know if there is a part that needs cleaned or replaced to prevent further problems.

If you got any more queries, don't hesitate to ask.
And If you Problem was solved, Kindly do Rate! Regards, Waqar.

Check Canon's website. All the software is available there.

Hi,
Well this printer is not compatible with Vista as the specification shows.

Thanks!
mannu_rakesh

Download from:

http://www.benq.co.in/support/downloads/downloads.cfm?product=2193

Try this document for service personel.Good luck.

http://al101fr.free.fr/notices/Imprimantes%20scanners%20photo/imprimante%20canon%20Service%20manual%20Canon%20i350,i355,i250,i255%20manuel%20notice.pdf

bassically your printer has come to the end of its life, you can either buy a new printer or contact the service center...

5100 is a carriage error. check the timing strip for contamination (plastic strip about 1/4" in width). Check for obstructions.
more information on this error can be found at http://www.fixyourownprinter.com/forums/laser/25975

Hi

Did placing the print head back in solve the issue? If not, please provide the error which comes up.

Thanks.

I think your ink cartridge is not genuine and it will affect your printer performance

I called Canon. I also had green 1 flash and amber 1flash everytime I turned on the printer. That right there indicates an elecrical problem. The flashes mean it needs serviced and with it not printing now means it's not wirth fixing, out of warranty. Canon did offer a code for reduced price new or referbished print from them.

Time to upgarde your printer unfortunatley.
Canon has an emulation workaround for printing only if you visit thier website.

Service 5200 means the printhead exceeded the temprature limititation try replacing the print head

Okay, follow these steps below to reset this message:

1) Enter SERVICE MODE. By pressing Menu-Copy-#
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

Then call Canon 1-800-828-4040

Just inform them that you have already reset the counter so the error is gone, but you needed to know if there is a part that needs cleaned or replaced to prevent further problems.

there is probably ink on the rollers. get some paper and just keep feeding it till the black marks stop. and RECYCLE the paper that you fed. DO NOT throw it out