20 Most Recent Canon imageRUNNER 3300 All-In-One Laser Printer - Page 3 Questions & Answers


ok the Error code is to do with your fixing unit, you need to go into service and clear the error then reset machine should work again.
do a search for clearing fixing unit error code on your canon copier, wont be to hard to find
canon copier tech

Canon... | Answered on Dec 06, 2017


E000 0000
The reading of the main thermistor does not reach 30°C 1 sec after the main
power switch is turned on. Or, it does not reach 70°C 2 sec thereafter.

Main cause:
The fixing film unit is faulty. The main thermistor has an open circuit. The
fixing heater has an open circuit. The main power supply PCB is faulty. The
DC controller PCB is faulty.

Caution:
To reset the error, execute the following in service mode:
COPIER>FUNCTION>CLEAR>ERR.

Action:
1. Connector
Is the connector of the fixing assembly connected?
a. main power supply PCB (J8) <-> relay connector <-> heater
b. DC controller PCB (J320) <-> relay connector <-> thermistor
NO: Connect the connector.

2. Fixing film unit (thermistor)
Check the interval between pin 1 and pin 2 and between pin 3 and pin 4 of
the connectosr (4-pin) of the thermistor for electrical continuity. Is it ¥W
(open)?
YES: The heater has an open circuit, or the thermal switch is open. Replace
the fixing film unit.

4. Main power supply PCB, DC controller PCB.
Press the Start key. Is the drive voltage of the heater supplied by the connector
J8 of the main power supply PCB?
Main heater: between J8-1 (FSR1) and J8-5 (FSR COM)
Sub heater: between J8-3 (FSR2) and J8-5 (FSR COM)
YES: The heater drive power supply is faulty. Replace the main power
supply PCB.
NO: The thermistor control mechanism is faulty. Replace the DC controller
PCB.

Canon... | Answered on Nov 29, 2017


this looks good
...to code error E000007-0000 http://www.copytechnet.com/forums/canon/2954-imagerunner-2200-error-e000007-0000-a.html canon 3320irE000007-0000 how to solve my problem error e000007-0000 error

Canon... | Answered on Nov 06, 2017


http://printcopy.info/?l=en&mod=free&chap=erc&brand=Canon&model=iR3300&code=E003-0000

I’m happy to help further over the phone at https://www.6ya.com/expert/joshua_ac64e182ed26f66d

Canon... | Answered on Sep 05, 2017


you must change your cleaning blade

Canon... | Answered on Aug 28, 2017


IF you have an E1 finisher on it, Turn OFF copier the E580 error is most likely related to the stack tray lift motor. Try disconnecting the finisher. That means pulling it away from the copier and unplugging the cable from the back of the copier. Turn the copier back on. This won't solve your problem, but you should be able to use the copier until a tech can have a look at it.

Canon... | Answered on Aug 28, 2017


how can i clear this problem

Canon... | Answered on Aug 19, 2017


if cannon ir 2200-3300 shows error E00805-0000 THEN fixing fan is not workig fan is jam oiling d fan then fan is not work change fixing fan.

Canon... | Answered on Jul 22, 2017


check the power supply first. is there any voltage fluctuations? Go to service mode. Addl. function>2&8>Addl. function> select copier. function>clear>err>ok. switch off the machine, wait for 15 minutes & turn on

Canon... | Answered on Jul 05, 2017


E064 The presence of a high-voltage error is communicated by the composite power supply PCB. (The output for primary charging, developing, or transfer
has deviated from a specific level of voltage.)
Main cause The contact has poor connection. The wiring is faulty. The composite power supply PCB is faulty. The DC controller PCB is faulty.
Action
1. Contact
Is any of the contacts of the primary charging roller, developing assembly, or transfer charging roller soiled? Or, is there poor contact?
YES: Clean the contact, and set it once again.
2. Wiring
Is the wiring between the contacts for the following normal: DC controller
PCB (J301), composite power supply PCB (J136), primary charging roller, developing assembly, transfer charging roller?
a. DC controller PCB (J301) <-> composite power supply PCB (J136)
b. composite power supply PCB (J130-7) <-> primary charging roller contact
c. composite power supply PCB (J130-1) <-> developing assembly contact
d. composite power supply PCB (FT133) <-> transfer roller contact
NO: Correct the connection.
3. Composite power supply PCB, DC controller PCB
Try replacing the composite power supply PCB. Is the problem corrected?
YES: Yes.
NO: Replace the DC controller PCB.

Canon... | Answered on Jun 22, 2017


I'm assuming that you mean blank copies. Open the document feeder as though you were going to make a copy on the glass. In the upper left corner you should see a curved shaped arm sticking up. Press that down to see if the scan lamp comes on, careful its a very bright light. If it doesn't then you will either have to replace the lamp, the lamp Inverter PCB Assy, or the lamp cable. This will most likely require a service call. Sorry.

Canon... | Answered on Jun 06, 2017


good morning sir, my ir machine is 3300 the problem is showing to my machine is E000003-0000 please suggest me answer

Thanks

Canon... | Answered on May 19, 2017


hi. what can we do for you?

Canon... | Answered on May 03, 2017

Not finding what you are looking for?
Canon imageRUNNER 3300 All-In-One Laser Printer Logo

1,163 questions posted

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

old marine
old marine

Level 3 Expert

2279 Answers

Ekse

Level 3 Expert

13434 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Canon Office Equipment & Supplies

  • Canon Office Equipment & Supplies

Most Popular Question

copier canon ir3300 error e000003 0000

  • Office Equipment & Supplies
Loading...