Sunbeam 1964,1965,1966,1967 Tiger Badge/pin 64,65,66,67 - Answered Questions & Fixed issues

Hi can somebody please send the ford telstar fs 2litre 1993 distributor module and coil colour code please 6pin and 3 pin

Have you checked the flasher relay. When the hazard switch is on and the breaks are pressed they will stop the hazard lights from flashing until the break is released in most cars. The turn signal only controls one side at a time and will not be effective when the hazard lights are switched to on.

http://www.classicbike.biz/triumph/Repair/1970s/70-Triumph-Repair-Manual-63-70.pdf Try this link to download the workshop manual. It have all details. Gopakumar Gopalan Google

Start by getting a current schematic. If you are doing the whole dash, I would investigate several manufactures that have a pre-built wiring harness. Otherwise, buy some automotive wire and have at it.

check cables and wiring to battery, engine, alternator, and body. Maybe you have a stray current draining the battery while the car isn't running. Grab some wrenches and test equipment.

maybe a vacuum leak, a wiring issue, or a fuel delivery problem. What code is exactly coming up? Example: P0171 - o2 sensor too lean

could be a stereo wiring problem. The illumination wire is obviously tied to battery voltage somewhere.

I have a 2001 buick century and the instrument cluster and tail lights are not working - my friend changed the instrument cluster and head light switch and nothing still works. What do I do next?

Sure, here are a few suggestions on where to find a replacement controller for your Sunbeam BL0750 electric blanket:

* **Sunbeam customer service:** You can contact Sunbeam customer service directly and they may be able to help you find a replacement controller. Their contact information is available on their website.
[Image of Sunbeam customer service website]
* **Online retailers:** There are a number of online retailers that sell replacement controllers for Sunbeam electric blankets. A quick search should turn up a few options.
* **Local hardware stores:** Some local hardware stores may also carry replacement controllers for Sunbeam electric blankets. It's worth checking with your local store to see if they have any in stock.

Once you've found a replacement controller, you can either install it yourself or have a professional do it for you. If you're not comfortable installing the controller yourself, you can take your blanket to a qualified electrician or repair shop.

Here are some additional tips for troubleshooting your Sunbeam BL0750 electric blanket:

* Check the power cord to make sure it's plugged in securely.
* Try using a different outlet.
* Check the fuse or circuit breaker to make sure it's not tripped.
* If you've tried all of these things and the blanket still doesn't work, you may need to replace the controller.

I hope this helps!

There is chance that arcing brushes in the motor are causing the odor. They should be replaced and the armature cleaned. A sunbeam repair shop can refurbish your mixer if the parts are still available.

Nothing works. Have had it for 6 months. Plugged in after so long, still blinking.

compressor not working or low on freon

A partstore knows or chec online

heating element possible shorted out.

Try these: -Make sure the remote battery contacts are clean; -clean fully charged battery surfaces with a lead pencil eraser to remove oxide; -could be loose contacts or cold solder joint on remote control board, especially if dropped a lot. if not tech savvy probably better to recycle old unit and purchase a new one . good luck!

Generally means u have a bad connection at the wall or at the control module. Disconnect everywhere u can and reconnect

Possible free manual if this is the same model with wick information. http://www.milesstair.com/Sunbeam3602.pdf

Try unplugging the power cord from the wall socket and check that the connection to the blanket is good and not loose. Then plug back into the wall socket and switch on. If error still occurs then there may be a problem with the blanket.

My sunbeam XL heating pad started blinking and I couldn’t figure it out. I Unplugged a couple of times and still it kept flashing. After hours of reading post, I did what wpart suggested and now it works normal again..... I kept pushing th on off button while plugged in, I unplugged it while still hitting the on off button, I plugged it back in while still hitting the on off button annnddddd drum roll please!!!!!! It started working properly! Thanks wpart, your the MVP and award goes to you!

Wires probably damaged inside. Be carefull, I had one cought on fire. Dont like this things ever since