Roper RS22AQXKQ Side by Side Refrigerator - Answered Questions & Fixed issues


Could be that the gearing on augur is tripped and that is why it stops.

Check attached site for parts and pricing.

Search Over 2 1 Million Appliance Parts

Roper RS22AQXKQ... | Answered on Sep 01, 2017 | 42 views


500 for 4 hrs

Roper RS22AQXKQ... | Answered on Oct 19, 2014 | 42 views


Not all fridges with water dispensers have integral filters. Several have an external in line filter fitted to the supply pipe.

Roper RS22AQXKQ... | Answered on Jul 16, 2014 | 269 views


First I would check cold control. Thats where you turn it off, if your temp is not warm. it can
be defective and not shutting off. If your temp is warm proceed with the following.
I would check the fan in the freezer. Listen to see if it is running
It moves air to the ref from the freezer
Then check to see if freezer control is turned WARMER, which makes the Ref. colder
Also this might be a common Defrost problem, Ice
is not being melted by the defrost system.The fan can't blow through the coils into the fridge.
Take out back panel of freezer to check for ice buildup. The coils should be clean.
There are three components to a defrost system- a heater,heater thermostat, and a timer unless you have a defrost electronic card.
Its best handled by a Technician but you could possibly do it by taking your model number to the nearest appliance parts store and asking for the parts. They are mostly located in freezer ,behind back panel on freezer coils.except the card which is usually located in ref The parts store will have info
Also check fan undernearh Ref in the rear
Clean condenser coils underneath
Check cold control (thats where you turn it colder)
.I'm including my article on Refrigerator Repair for your help and convenience.;
Please click or copy and paste into browser for Article
http://www.fixya.com/support/r5816737-fix_refrigerator_psychologically
Thanks for using fixya
Leo Ponder
imufo2
Please VOTE FOR ME If this was helpful

Roper RS22AQXKQ... | Answered on May 03, 2014 | 83 views


Just measure the outside height, depth and width. A replacement of the same or bigger dimensions will hold as much or more stock

Roper RS22AQXKQ... | Answered on Apr 30, 2014 | 196 views


Wrilpool w/ French doors 2 yrs old leaking at the bottom. There's ice buildup at the bottom. Bill

Roper RS22AQXKQ... | Answered on Mar 10, 2013 | 43 views


Turn water supply to refrigerator off and get a pan or towels to collect what water that will spill when disconnected. On each end of the quick connect coupling is a ring hold the coupling tight with one hand while pressing the ring towards the center of the coupling and then pull the water line out. When replacing the water line trim the part of the water line off where the ring was before or the line may leak once you reattach the water line. Press ring towards the coupling to remove and simply push the existing line after trimming into coupling and pull tight. The grip inside the coupling will lock the line in place. If you have questions please let me know, Thank You Sea Breeze

Roper RS22AQXKQ... | Answered on Nov 17, 2012 | 381 views


Take a look at this video.

Roper RS22AQXKQ... | Answered on Oct 18, 2012 | 102 views


Defrost completely. The unit is probably iced up. Make sure your gaskets are clean and sealing well. If it happens again, we need to find out why. Also...clean the condenser.

Roper RS22AQXKQ... | Answered on Sep 17, 2012 | 203 views


The line going into the dispenser is a 5/16 line. You'll have to remove the front of the dispenser on the door to get access to the line to unclip it. Once you have that done you can pull the line out from the bottom. At this point there are a variety of different unions, compression fittings, etc. to splice the line. After that you just feed the line back through the bottom of the door, clip it back in place, put the dispenser back together and your done.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3

Roper RS22AQXKQ... | Answered on Sep 17, 2012 | 167 views


First if you don't already have Adobe Reader on your computer click

here=> 8_6_2012_7_21_48_pm.gif You will need Adobe Acrobat Reader to view these documents. The Adobe Acrobat Reader is available as a free download. Then go to Whirlpool Manuals, Guides and Instructions and select select the type of visitor that best represents you in the drop down menu and select CONSUMER and then below the dropdown enter RS22AQXKQ and then click GO.And that should take to to a page that offers manuals and repair list. Or simply click here=> RS22AQXKQ00.pdf for the user manual or here=> for the repair parts list=> RS22AQXKQ00.pdf If you have questions please let me know, Thanks Sea Breeze
Whirlpool-made Roper

Roper RS22AQXKQ... | Answered on Aug 06, 2012 | 1,714 views


Most likely the valve has failed. Usually located in the back of the refrigerator, near the bottom - otherwise, follow your water line (feed from the house water supply).

Roper RS22AQXKQ... | Answered on Aug 02, 2012 | 665 views


Make sure your refrigerator is level. Once your refriderator is level you should also check that your ice maker is level. You have some range of movement of the screws that attach the ice maker to the refrigerator if you loosen the screw and push up on the ice maker then re-tighten the screw.

Roper RS22AQXKQ... | Answered on Jul 20, 2012 | 56 views


Hi, When that strip gets hot, it is a sign the temperatures are not cold enough. Put a thermomitor in the freezer. You should get a reading of 0 to 5 above. If not, let me know and we can try and get you through this.

Thanks
Vic

Roper RS22AQXKQ... | Answered on Jun 09, 2012 | 442 views


You will need Adobe Acrobat Reader to view these documents. The Adobe Acrobat Reader is available as a free download. I will list the Parts Manual for your Click Here=> RS22AQXKQ00_Repair_Parts.pdf First you need to remove the plastic hinge cover's. On page 1 of the PDF you will see the top hinges marked as location 10 and 11 Make sure power is disconnected before removal of the freezer door and fresh food section door. Loosen the top hinges and disconnect the wiring harness just below the top left plastic hinge cover. Also remove the kick plate listed as location 16 and just behind the kick plate and below the freezer door push the snap lock water connector that joins water lines. Then carefully lift doors and place where they will not fall or be damage water line during time doors are of refrigerator. If helpful please rate ans should you have questions please ask, Thanks Sea Breeze

Roper RS22AQXKQ... | Answered on Jan 06, 2012 | 135 views


Could be the defrost heater as well. Some units use a adaptive control instead of a defrost timer.

If you were to take everything out of the inside of the freezer and look at the rear wall of the inside of the freezer you will notice there are screws on this panel so that this panel can be removed. Once you removed this panel this would give you access to the evaporator coil. If you look above the coil you will see the culprit that makes them awesome noises you enjoy so much. If you see any ice build up anywere in this area you would defrost it with a hair dryer. This issue is called a defrost problem that your unit is experiencing. This is due to one or more of three basic parts. Two of those parts are located right in the area where you have accessed the evaporator coil. You would need a multimeter and be able to perform an ohms test on each of these next two parts mentioned to diagnose which part or if both had a fault. The first part is called the defrost thermostat which is a small round sensor that is clipped onto one of the copper lines near the top of the evaporator coil. Here is a link to click that is the entire schematic for your machine if the last numbers after the q that you posted were 03 there are three models an 04 as well as an 00. The 03 has 3 more parts listed then the others. http://www.searspartsdirect.com/partsdirect/part-model/Roper-Parts/Refrigerator-Parts/Model-RS22AQXKQ03/0893/0165000?searchedModel=RS22AQXKQ&blt=11
you would then go into the unit section and click that as well your defrost thermostat is part number 35 and the defrost heater is part number 33 do the testing on these parts and if you find no fault message me back and I will explain more on the defrost timer or adaptive control due to the look up site just went down for maintenance. If you have any questions message me those back as well. Thank you
Rick

Roper RS22AQXKQ... | Answered on Nov 24, 2011 | 75 views


If you were to take everything out of the inside of the freezer and look at the rear wall of the inside of the freezer you will notice there are screws on this panel so that this panel can be removed. Once you removed this panel this would give you access to the evaporator coil. If you look above the coil you will see the culprit that makes them awesome noises you enjoy so much. If you see any ice build up anywere in this area you would defrost it with a hair dryer. This issue is called a defrost problem that your unit is experiencing. This is due to one or more of three basic parts. Two of those parts are located right in the area where you have accessed the evaporator coil. You would need a multimeter and be able to perform an ohms test on each of these next two parts mentioned to diagnose which part or if both had a fault. The first part is called the defrost thermostat which is a small round sensor that is clipped onto one of the copper lines near the top of the evaporator coil. Here is a link to click that is the entire schematic for your machine if the last numbers after the q that you posted were 03 there are three models an 04 as well as an 00. The 03 has 3 more parts listed then the others. http://www.searspartsdirect.com/partsdirect/part-model/Roper-Parts/Refrigerator-Parts/Model-RS22AQXKQ03/0893/0165000?searchedModel=RS22AQXKQ&blt=11
you would then go into the unit section and click that as well your defrost thermostat is part number 35 and the defrost heater is part number 33 do the testing on these parts and if you find no fault message me back and I will explain more on the defrost timer or adaptive control due to the look up site just went down for maintenance. If you have any questions message me those back as well. Thank you
Rick

Roper RS22AQXKQ... | Answered on Nov 24, 2011 | 81 views


Hello, The motor that you are refering to is the evaporator fan motor. If you were to take everything out of the inside of the freezer and look at the rear wall of the inside of the freezer you will notice there are screws on this panel so that this panel can be removed. Once you removed this panel this would give you access to the evaporator coil. If you look above the coil you will see the culprit that makes them awesome noises you enjoy so much. If you see any ice build up anywere in this area you would defrost it with a hair dryer. This issue is called a defrost problem that your unit is experiencing. This is due to one or more of three basic parts. Two of those parts are located right in the area where you have accessed the evaporator coil. You would need a multimeter and be able to perform an ohms test on each of these next two parts mentioned to diagnose which part or if both had a fault. The first part is called the defrost thermostat which is a small round sensor that is clipped onto one of the copper lines near the top of the evaporator coil. Here is a link to click that is the entire schematic for your machine if the last numbers after the q that you posted were 03 there are three models an 04 as well as an 00. The 03 has 3 more parts listed then the others. http://www.searspartsdirect.com/partsdirect/part-model/Roper-Parts/Refrigerator-Parts/Model-RS22AQXKQ03/0893/0165000?searchedModel=RS22AQXKQ&blt=11
you would then go into the unit section and click that as well your defrost thermostat is part number 35 and the defrost heater is part number 33 do the testing on these parts and if you find no fault message me back and I will explain more on the defrost timer or adaptive control due to the look up site just went down for maintenance. If you have any questions message me those back as well. Thank you
Rick

Roper RS22AQXKQ... | Answered on Nov 24, 2011 | 256 views


Hello, josh

I am trying to help you out here. Maybe this will help some? I am know on Fixya as the cleanup expert pro. Which means I spend my own personal time to seek out customers that maybe have not had there problem yet solved by the other fantastic great experts. I do this on my own for free. Think of me as a Specialized Trouble Shooter.

I have found out that it appears that lots of customers appreciate my efforts and help. So, I thought I would take some of my own personal time
to see if I can help you. Even though this Informational site may not have your exact model or brand, But this site will help you a lot. Here is the site link about everything you want to know about refrigerator and possibly yours, from repair to trouble shooting it.

http://home.howstuffworks.com/how-to-repair-a-refrigerator.htm





Please if this helped you at all, if you can find the time and in your heart to rate my help and some kind words written would be appreciated for my free help, I would appreciate it. Like I said I just try to help, If anything this is good information for future problems. If you felt that my free help was a waist of time for you, I'm sorry. I do not get paid to help people on the site, I do it cause I like to help and maybe make a smile on someones face.

Here is also my direct link to my own pages of other areas of my expertise for other problems you might have in Automotive, Appliance, and Electronics. Drop In anytime for my help.


http://beta.fixya.com/users/mc1bean

Thanks Mike

Roper RS22AQXKQ... | Answered on Oct 31, 2011 | 162 views


Hello,

I am trying to help you out here. Maybe this will help some? I am know on Fixya as the cleanup expert pro. Which means I spend my own personal time to seek out customers that maybe have not had there problem yet solved by the other fantastic great experts. I do this on my own for free. Think of me as a Specialized Trouble Shooter.

I have found out that it appears that lots of customers appreciate my efforts and help. So, I thought I would take some of my own personal time
to see if I can help you. Even though this Informational site may not have your exact model or brand, But this site will help you a lot. Here is the site link about everything you want to know about refrigerator and possibly yours, from repair to trouble shooting it.

http://home.howstuffworks.com/how-to-repair-a-refrigerator.htm





Please if this helped you at all, if you can find the time and in your heart to rate my help and some kind words written would be appreciated for my free help, I would appreciate it. Like I said I just try to help, If anything this is good information for future problems. If you felt that my free help was a waist of time for you, I'm sorry. I do not get paid to help people on the site, I do it cause I like to help and maybe make a smile on someones face.

Here is also my direct link to my own pages of other areas of my expertise for other problems you might have in Automotive, Appliance, and Electronics. Drop In anytime for my help.


http://beta.fixya.com/users/mc1bean

Thanks Mike

Roper RS22AQXKQ... | Answered on Oct 31, 2011 | 57 views

Not finding what you are looking for?
Roper RS22AQXKQ Side by Side Refrigerator Logo

232 questions posted

Ask a Question

Usually answered in minutes!

Top Roper Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Bruce Denton

Level 2 Expert

273 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you a Roper Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...