20 Most Recent Samsung Dv5471agp 27" Front-load Gas Dryer - Page 4 Questions & Answers

If you do not know much about fixing them, call a repair man. If you like to tinker, take off the back cover and see what is clicking.

Because of comments I saw online I bought a new control board but There is another control board that may be impacted and I am trying to troubleshoot before I buy another board. Thank you for your question. I am reviewing it and will respond in a moment. AE6 represents communication errors between the sub and main PBAs or the main and inverter PBAs. Turn the unit off from the breaker for about2 minutes, then turn it back on, if that does not clear the error code, you will need to call out a service tech because you have a more serious problem, you can get a service tech here. https:/www.searshomeservices.com/repair Is there any troubleshooting you can recommend to determine what part to replace? Yes, you will need to replace the main and sub PCB on the unit. Thank you

AE6 error code indicates communication error specifically. The commands from the logic circuit are being interrupted, interrupting the program from moving forward.

Hey Randy, thank you for reaching out. According. to my research E3 fault code appears when the water level increases dramatically and reaches the overflow point. This can be due to a blocked pressure system. Please, make sure your supply hose is not bent or kinked. I hope this is what you are looking for.

The 'smoke' is steam from the heater element, it is still warm. It is a fully electronic machine and sounds like you need a Samsung engineer. Here is the service manual. https://applianceassistant.com/ServiceManuals/WF220-Fast-track-R3.pdf ..

The drain hose is not installed properly or is clogged.

try to lubricate latch or try to jump it for test if bad replace it should only be held by a clip

check belt if ok possible cogs under agitator to tub

Plug it in. Does it have a reset button? Check the fuse.

possible belt debris

The thermal fuse is not working and there could be an over heating issue going on and your washing machine will not be able to work again unless the thermal fuse has been replaced.

I have a different brand top loader but the agitator uses these plastic "dog ears" that catch a ring gear. They are turned to only catch in one direction, allowing the agitator to turn one way. As they wear down the agitator stops turning at all and they make a plastic grinding noise. Your model may have something similar. Look up your model and see what might be in the agitator to replace.

If your washer isn't spinning properly , it could be because of an unbalanced load, which makes it harder for the drum to spin. An unblanced load also cause errors. "Ub" or "Ur" display is one of the sign that your washer is unbalanced. This may be because the washer is lopsided or because the load inside is uneven. Or A faulty drain pump could cause a Samsung washer not spinning or draining water. The drain pump is responsible for emptying the washer of its dirty water after it has completed washing, but when it clogs or jams, it's unable to empty the machine, and your clothes won't get clean. This is an issue with the machine.

The water supply for your washing machine is having problems or the water supply hose is either kinked or is blocked. The debris filter and the mesh filter need to be cleaned out.

Ensure the outlet drain pipe is raised higher than the drum/water level to stop the syphoning of the water.

Did you replace the timer?

$181.83. It is an expensive part!! https://www.searspartsdirect.com/product/3j9yg5gbt2-0026-401/id-dc97-18094c $121 on Reliable Parts. eBay out of stock https://www.google.com/search?q=samsung+wf42h5400+door+boot+seal ..

Check the lid switch it may not be making the circuit or needs replacing.

The locking mechanism for your washing machine could might be jammed here. Maybe some clothes could of had got in the way. Or there could be a glitch in the washing machines computer system The washing machine could also not be draining correctly ,and is leaving the washer door locked and the drum filled up with water.Unplug the washer for about 5 minutes to reset the system and the machine and see if it solves the problem. If still no luck then you will have to call a repair person to take a look and see what the problem is. It could be the hose needs to be replaced or the motor is not working anymore.