Top 20 LG Wm3470hva Wm3470hva Front Load Washer Questions & Answers

You mean pushing the power button will not power unit back on?

Take the reimbursement because the minute scratch is not effecting the performance and you are the only one who is aware of the condition. As for the noise, a bit of One Lube spray on the hinge will take care of that. One Lube is a special oil/silicone application that works on all moving parts that tend to make noise, and it lasts far longer than all other products. Look for it on the internet, or ACE Hardware.

6his can happen when you either overload the washer or you have a low amount of stuff in but it is heavy. would seem 4.0 is the max you can have in the drum at a time. if it persists at this with varying loads. then the shockers have gone weak and need replacing. or the drum has come out off balance. this can because of the bearing or something has dented the drum. somtimes putting shoes in to was can do this type of damaged.

Unplug the washer from the wall wait about 5 minutes, plug it back in to the wall and press the power button. You should see all of the lights on the front come on and start cycling. wait about 2 minutes and you should be ready to start washing.

its best to get an engineer to the problem as it could be anything at all or just an alignment problem eric

Sounds like the dial timer is defective, I am not affiliated with this site, https://www.repairclinic.com/Video

https://electronicshelponline.blogspot.com/ http://homenol.blogspot.com/ Visit this site to get some details.

Remove the screws that attach the top panel at the back of the machine, slide the top backwards and remove the top panel. Run the machine as per normal, but be careful as the electrics will now be exposed, you will be able to see where the water is leaking from and be able to repair/replace defective part.

If you wish to get some details; check the site linked here. Pull up older posts........ http://electro-medical.blogspot.com/

take the back off see if the water pump making that noise or is broken should look something like this one

This dE error or fault code to indicate that the door is not latching properly. Check the lid or door operation to be sure it's not binding and that the door alignment is correct. Also, check the door/lid hinges to be sure they're not binding. Finally, make sure the door catch is in place and not broken. You may need to replace the door hook/catch or the door lock assembly.

2 possible causes the water solenoid control valve is split in the diaphragm and not stopping the water the small hose from the base of the tub to the level control pressure unit is split or disconnected or the pressure unit has failed and is not activating the water control valve

Take out the soap drawer and clean the fabric softner compartment. This happens when there is residues left. And it gets clogged up.

Please do not do another load of wash until this problem is fixed, or you may find yourself with a house/apartment fire! I am thinking your motor (most likely) or the controls (least) have a short, and are causing your problem. Oh, yes. Take a really good look at the circuit breaker box inside, because a broken or loose ground wire ( there are two) can also cause this problem. One ground wire should be white, one should be bare. Each should be securely screwed into the lugs of the grounded section of the circuit breaker box. God bless your efforts.

more often than not, this is a problem with a faulty heater in the machine not getting it up to temperatre (which help the powder dissolve). Put it on a 90 degree wash and keep checking the temperature, if it's not getting hot, then you need to swap out the heater. Ift IS getting hot, then it could be an empty pump problem. If the pump or waste pipe are blocked, the wash will take a very long time but it will be struggling to evacuate water and add fresh, which will also causse powder residue to be left behind. But I'd put my money on a heater fault

Hi Elaine258, you may need to take a look into it from the top, the soap, softener dispenser may be catching. Fairly straight forward to do, disconnect from the mains, two fasteners at the back hold the top on (if I remember right) lift top up from back and push forward, vvwalla. Hope this helps.

pull back the lip and look for a wire and spring that goes around the gasket. check out repair videos on repairclinic.com or appliancepartspros.com.

open door and see if the drum can be moved up and down or side to side a lot. if it can, then you need a new bearing most likely. this would most likely only happen on a older washer that has been used quite a bit. repairclinic.com and appliancepartspros.com both have very good videos to show how the bearing can be replaced. takes some time and work, but if everything else on the washer is good, it could be worth the trouble. good luck.

Hi Declan.....need to know which model machine you have.

The FE code is an excessive water supply if the water is continuously running into the machine it may be due to a failing inlet valve or stuck float switch since you mentioned the drain pump filter being changed it could be that the old filter was restricting the flow.