LG WM3875HVCA Laundry : Front Load Washers - Answered Questions & Fixed issues


oh oh bad timer

LG WM3875HVCA... | Answered on Oct 04, 2014 | 40 views


This dE error or fault code to indicate that the door is not latching properly. Check the lid or door operation to be sure it's not binding and that the door alignment is correct. Also, check the door/lid hinges to be sure they're not binding. Finally, make sure the door catch is in place and not broken. You may need to replace the door hook/catch or the door lock assembly.

LG WM Washing... | Answered on Oct 29, 2018 | 227 views


its best to get an engineer to the problem as it could be anything at all or just an alignment problem eric

LG WM Washing... | Answered on Dec 27, 2017 | 57 views


Sounds like the dial timer is defective, I am not affiliated with this site, https://www.repairclinic.com/Video

LG WM Washing... | Answered on Apr 25, 2017 | 35 views


http://www.lg.com/au/support/support-product/lg-WT-H9556

LG WM Washing... | Answered on Mar 29, 2017 | 399 views


There is no need to raise the water level. all modern washers automatically add the amount of water needed to wash the amount of clothes that you put in, I could explain how, but it will put you to sleep. rest assured these machines pretty much look after themselves. I would be more interested to know why you think it needs more water, are you having rinsing issues? wash quality issues?

LG WM Washing... | Answered on Oct 18, 2016 | 1,220 views


Remove the screws that attach the top panel at the back of the machine, slide the top backwards and remove the top panel.
Run the machine as per normal, but be careful as the electrics will now be exposed, you will be able to see where the water is leaking from and be able to repair/replace defective part.

LG WM Washing... | Answered on Aug 15, 2016 | 76 views


If you wish to get some details; check the site linked here. Pull up older posts........

http://electro-medical.blogspot.com/

LG WM Washing... | Answered on Jun 12, 2016 | 57 views


take the back off

see if the water pump making that noise or is broken

should look something like this one
26197828-pe3l0ypp1vfpknq0mkt0qwu4-3-0.jpg

LG WM Washing... | Answered on May 18, 2016 | 94 views


run a wire thru it no doubt it is plugged with crud

LG WM Washing... | Answered on May 02, 2016 | 168 views


There probably isn't one. If you are certain power is getting to the machine, there may have been control failure.

LG WM Washing... | Answered on Apr 25, 2016 | 95 views


2 possible causes
the water solenoid control valve is split in the diaphragm and not stopping the water
the small hose from the base of the tub to the level control pressure unit is split or disconnected or the pressure unit has failed and is not activating the water control valve

LG WM Washing... | Answered on Mar 25, 2016 | 156 views


Take out the soap drawer and clean the fabric softner compartment. This happens when there is residues left. And it gets clogged up.

LG WM Washing... | Answered on Feb 17, 2016 | 124 views


The obvious question is how do you know that it is soap? What washing machine is it? The biggest problem with most washing machines is that people use too much soap to begin with. I would go to a store and get a new t-shirt or something. Run the machine with nothing in it. Then put the shirt in and run it again without adding any soap. When it is done check the shirt for soap. There could be a build up on the inside of the drum.

LG WM Washing... | Answered on Feb 13, 2016 | 126 views


Please do not do another load of wash until this problem is fixed, or you may find yourself with a house/apartment fire!
I am thinking your motor (most likely) or the controls (least) have a short, and are causing your problem.
Oh, yes.
Take a really good look at the circuit breaker box inside, because a broken or loose ground wire ( there are two) can also cause this problem.
One ground wire should be white, one should be bare.
Each should be securely screwed into the lugs of the grounded section of the circuit breaker box.
God bless your efforts.

LG WM Washing... | Answered on Jan 12, 2016 | 75 views


pull back the lip and look for a wire and spring that goes around the gasket. check out repair videos on repairclinic.com or appliancepartspros.com.

LG WM Washing... | Answered on Jan 10, 2016 | 71 views


more often than not, this is a problem with a faulty heater in the machine not getting it up to temperatre (which help the powder dissolve). Put it on a 90 degree wash and keep checking the temperature, if it's not getting hot, then you need to swap out the heater. Ift IS getting hot, then it could be an empty pump problem. If the pump or waste pipe are blocked, the wash will take a very long time but it will be struggling to evacuate water and add fresh, which will also causse powder residue to be left behind. But I'd put my money on a heater fault

LG WM Washing... | Answered on Dec 26, 2015 | 115 views


something is blocking the pump.unplug first.take drain hose and hold down at floor level with a container to catch water.it may be a coin or a wire from a bra,hair bobble etc feel in the pump to see if the impeller is free to move.if it is then suspect something in the hose between drum and pump like a sock.that restricts flow enough to put up fault code

LG WM Washing... | Answered on Nov 18, 2015 | 94 views

Not finding what you are looking for?
LG WM3875HVCA Laundry : Front Load Washers Logo

3 questions posted

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...