LG WM2010CW 3.5 cu. ft. Front Load Washer - Answered Questions & Fixed issues


If your washer doesn't go through the washer rinse cycle, the most likely cause is the water valve. What happens is the water valve will stop letting cold water into the washer; therefore, once the washer gets to rinse it will either stop or not do anything during the whole rinse cycle.
This is because when you selected your water temperature, you may have selected warm/cold or hot/cold. The hot water came in and you didn't notice any problems. When it got to rinse, the cold water the cold water won't come in. Therefore, the washer does nothing.
The item to check would be your water inlet valve. Check it for continuity with a multi meter it should show Ohms or a closed circuit. To test it when water is overflowing unplug the unit and see if it still overflows or continues to fill. If it stops when unplugged. Then it is not a water inlet problem but an electrical signal problem going to ur water inlet valve. Possibly from the panel or board. You can also do a live volt test to see if it is getting the full 120 current, but be sure to unplug unit before testing as this is a live test.
Another test u can do to check the water inlet valve, first cut the water off and remove the hoses off the back of the washer. Then one at a time point the hoses inside the washer tub and turn the water back on. If you don't have good water pressure, turn the water back off and remove the strainer that should be in one end of the hose. Inspect the strainer to see if it is stopped up, clean it and reinstall it. Now repeat this test. If you have good water pressure now, reinstall hose and your problem is fixed.
If you still don't have good water pressure, the problem is in your house plumbing and you need to call a plumber. If you had good water pressure the first time you performed the test, the water valve is bad and needs replacing.
TIMER
If your washer doesn't go through the washer rinse cycle the timer may be the problem. Sometimes the timer gets stuck in the middle of the cycle or won't turn at all. If the washer runs, but the timer doesn't turn, the timer is bad and needs replacing.
Do you have anti-flood hoses leading to the machine. If you do there is probably a loose tube in the back causing a small leak. When the hoses detect that water is still flowing after a certain amount of time due to the leak it shuts down and causes the machine to turn off during the rinse/spin cycle
By the way my advice is free cuz God is good!







13821863-0ibogqi43422e0jrk2ickvgv-2-0.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-2.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-5.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-9.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-14.jpg

13821863-0ibogqi43422e0jrk2ickvgv-2-20.jpg

LG WM2010CW 3.5... | Answered on May 26, 2015 | 431 views


Go to LG web site and see support see if others have this problem and if there is a recall. let them know about this problem and make them help you.

LG WM2010CW 3.5... | Answered on May 10, 2015 | 144 views


On most washers, IE error means that the washer is not seeing proper hot and/or cold water inputs. Check the hoses for kinks. Ensure the water valves are fully open. If these are not faulty, turn off the water, remove the hoses at the back of the washer, and check the input filter screens for clogging. This is a common problem.

LG WM2010CW 3.5... | Answered on Feb 26, 2015 | 38 views


This dE error or fault code to indicate that the door is not latching properly. Check the lid or door operation to be sure it's not binding and that the door alignment is correct. Also, check the door/lid hinges to be sure they're not binding. Finally, make sure the door catch is in place and not broken. You may need to replace the door hook/catch or the door lock assembly.

LG WM Washing... | Answered on Oct 29, 2018 | 226 views


its best to get an engineer to the problem as it could be anything at all or just an alignment problem eric

LG WM Washing... | Answered on Dec 27, 2017 | 57 views


Sounds like the dial timer is defective, I am not affiliated with this site, https://www.repairclinic.com/Video

LG WM Washing... | Answered on Apr 25, 2017 | 35 views


http://www.lg.com/au/support/support-product/lg-WT-H9556

LG WM Washing... | Answered on Mar 29, 2017 | 399 views


There is no need to raise the water level. all modern washers automatically add the amount of water needed to wash the amount of clothes that you put in, I could explain how, but it will put you to sleep. rest assured these machines pretty much look after themselves. I would be more interested to know why you think it needs more water, are you having rinsing issues? wash quality issues?

LG WM Washing... | Answered on Oct 18, 2016 | 1,195 views


Remove the screws that attach the top panel at the back of the machine, slide the top backwards and remove the top panel.
Run the machine as per normal, but be careful as the electrics will now be exposed, you will be able to see where the water is leaking from and be able to repair/replace defective part.

LG WM Washing... | Answered on Aug 15, 2016 | 76 views


If you wish to get some details; check the site linked here. Pull up older posts........

http://electro-medical.blogspot.com/

LG WM Washing... | Answered on Jun 12, 2016 | 55 views


take the back off

see if the water pump making that noise or is broken

should look something like this one
26197828-pe3l0ypp1vfpknq0mkt0qwu4-3-0.jpg

LG WM Washing... | Answered on May 18, 2016 | 94 views


run a wire thru it no doubt it is plugged with crud

LG WM Washing... | Answered on May 02, 2016 | 168 views


There probably isn't one. If you are certain power is getting to the machine, there may have been control failure.

LG WM Washing... | Answered on Apr 25, 2016 | 95 views


2 possible causes
the water solenoid control valve is split in the diaphragm and not stopping the water
the small hose from the base of the tub to the level control pressure unit is split or disconnected or the pressure unit has failed and is not activating the water control valve

LG WM Washing... | Answered on Mar 25, 2016 | 155 views


Take out the soap drawer and clean the fabric softner compartment. This happens when there is residues left. And it gets clogged up.

LG WM Washing... | Answered on Feb 17, 2016 | 124 views


The obvious question is how do you know that it is soap? What washing machine is it? The biggest problem with most washing machines is that people use too much soap to begin with. I would go to a store and get a new t-shirt or something. Run the machine with nothing in it. Then put the shirt in and run it again without adding any soap. When it is done check the shirt for soap. There could be a build up on the inside of the drum.

LG WM Washing... | Answered on Feb 13, 2016 | 126 views


Please do not do another load of wash until this problem is fixed, or you may find yourself with a house/apartment fire!
I am thinking your motor (most likely) or the controls (least) have a short, and are causing your problem.
Oh, yes.
Take a really good look at the circuit breaker box inside, because a broken or loose ground wire ( there are two) can also cause this problem.
One ground wire should be white, one should be bare.
Each should be securely screwed into the lugs of the grounded section of the circuit breaker box.
God bless your efforts.

LG WM Washing... | Answered on Jan 12, 2016 | 75 views


pull back the lip and look for a wire and spring that goes around the gasket. check out repair videos on repairclinic.com or appliancepartspros.com.

LG WM Washing... | Answered on Jan 10, 2016 | 71 views

Not finding what you are looking for?
LG WM2010CW 3.5 cu. ft. Front Load Washer Logo

16 questions posted

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85219 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...