20 Most Recent
LG WM3987HW 4.2 cu.ft. White Front Load Washer / Dryer Combo - Page 2 Questions & Answers
How can I replace door gasket?
pull back the lip and look for a wire and spring that goes around the gasket. check out repair videos on repairclinic.com or appliancepartspros.com.
WF-760 FUZZY LOGIC 7KG machine, Problem is, some washing powders remain in the cloths and not properly washing. earlier it works well.
more often than not, this is a problem with a faulty heater in the machine not getting it up to temperatre (which help the powder dissolve). Put it on a 90 degree wash and keep checking the temperature, if it's not getting hot, then you need to swap out the heater. Ift IS getting hot, then it could be an empty pump problem. If the pump or waste pipe are blocked, the wash will take a very long time but it will be struggling to evacuate water and add fresh, which will also causse powder residue to be left behind. But I'd put my money on a heater fault
What does an OE error msg mean and how do you fix this
something is blocking the pump.unplug first.take drain hose and hold down at floor level with a container to catch water.it may be a coin or a wire from a bra,hair bobble etc feel in the pump to see if the impeller is free to move.if it is then suspect something in the hose between drum and pump like a sock.that restricts flow enough to put up fault code
My LG front loader washer making noise in spin cycle, especially last 5 minutes, how to I fix this?
open door and see if the drum can be moved up and down or side to side a lot. if it can, then you need a new bearing most likely. this would most likely only happen on a older washer that has been used quite a bit. repairclinic.com and appliancepartspros.com both have very good videos to show how the bearing can be replaced. takes some time and work, but if everything else on the washer is good, it could be worth the trouble. good luck.
FE code on LG washer.
The FE code is an excessive water supply if the water is continuously running into the machine it may be due to a failing inlet valve or stuck float switch since you mentioned the drain pump filter being changed it could be that the old filter was restricting the flow.
Why my lg washing machine won't spin
No agitation?
first use a meter and check ur water pressure switch? that is what sends the machine the message to start wash cycle? You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube. If the machine starts to wash. the pressure switch is more than likely good. now take the original hose tube and plug one end and blow into it the other end, it should be hard and have pressure, if it is easy to blow and u dont feel any pressure and it feels like the air is going out ?
sometimes they get busted open or a pin hole and release air causing the water switch diaphram to not open.
If both check ok then next CHECK the motor coupler or belt if belt driven.check with a multi meter for continuity the door switch, and if there is a little movement on wash cycle in 1 direction only then check the cam dogs in agitator.
No spin, try these:
Using a multi meter check for continuity the door switch, which when bad may not allow agitation or spin. The lid switch assembly can fail either mechanically or electrically.
Check the clutch, brake assembly and transmission, one way to check for slipping is to get under the machine after a spin cycle ( this is if u get a lil spin but not much leaving clothes still wet) mix in a spray bottle a lil water and some dish detergent, then spray it on the clutch assembly ( the metal round pc. Connected to the tranny) if it sizzles and steams up then u know its bad and slipping. Another way to check clutch if u get no spin at all? Is to take it out and use ur hand to try and turn the inner spring assembly pushing it around the inside? If its very easy, it BAD should be hard to push by hand.
Next check the motor coupler which engages the tub and tranny to the motor. ( if its bad u usually get no wash or spin or very little of either)
Next check for a loose, worn or broken belt if belt driven.
Leaking water
its called the water inlet valve. they should have a rubber washer in each end of the hose and if they go bad , u get leaks.
Not finding what you are looking for?