Top 20 Edirol UA-25 External Sound System Questions & Answers

you should try it according to sound system.

Hello. Sometimes the USB voltage is not enougth. Try connect the usb cable into another USB port, preferring the rear panel connectors. The UA25 drivers must be installed previously.

Are you switching on the "MON.SW" button?

Be aware that SCMS "prohibited" recordings will trip this flashing light, and will not output. You will have to make an analog copy.

Hi there,I am not sure what platform you are using or what software, but I would recomend unistalling the edirrol completely. Then re-dowload all the drivers and re-install them completely. Remove all traces from your recording software also before reinstalling.Please give a bit more iformation on your setup if this is still a problem.Best of luck

no is the answer. Behringer gives out 8 channels of ADAT, the optical on your edirol is a stereo optical only and not adat compatiible

hmm, it could be something simple such as a faulty cable from mic to pc, it could be a faulty input if you are using a mixer, could be a faulty mic, it could even be a piece of software running in the background that is conflicting with sonar and causing this problem. This should be an easy problem for your "engineer" to sort out. as seeing it makes it 100 times easier to fault find. Thats part of being an engineer!

Restore your Computer to Original settings.
Download and install this driver for UA-25EX >>http://cms.rolandus.com/assets/media/zip/ua25ex_win7_x64_v100.zip

Be sure to try all available USB ports on your computer as some-times they get damaged and don't offer a good connection or they damage other components. Check your USB ports, make sure they look good, it's 4 flat neat connection pins/points. Over time they can be damaged, in which case a pin/point gets bent and pushed to the back of the plug meaning that it will either damage devices plugged into it or it will simply not function.

It might also be an idea to try this device in another computer to eliminate your computer as the faulty component.

Take care!
damnor01

1. check your user manual for clicks/pops.
this could be due to devices connected to the Edirol UA-25 or a television or microwave.
2. this also could be due to the setting in Windows Energy saving settings.
that is the Windows "sleep mode" and power saving mode.
3. this could also be due to the USB cable.
4. you may need an external filter device for the process you are using.
5. read your manual on Troubleshooting Noise ( clicks and pops).

I am using a laptop for my music creation and I am thinking about using an External Sound Card connected with a USB cable or getting an Sound Card. My integrated sound card has a little bit too much latency. Will I have just as much or more latency with the External Sound Card because it is connected with the USB cable or would I be better off with the Sound Card?
Thanks for vinu plz plz plz plz plz plz plz plz help me sir.

Connect it before powering system. The usual cause of no power on this is improper software configuration or assignment in the PC regarding the sound devices. It is NOT a "fuse" problem.
Make sure that when you go to "Sounds and Devices" in the control panel that the "Voice" tab is shown assigned to the UA-25. If not, make sure it is in the list of devices and assign it as default.

I am using a laptop for my music creation and I am thinking about using an External Sound Card connected with a USB cable or getting an Express Card Sound Card. My integrated sound card has a little bit too much latency. Will I have just as much or more latency with the External Sound Card because it is connected with the USB cable or would I be better off with the Express Card Sound Card?
Thanks for any help.
VINU

check the lead/s for this edirol make sure it has a secure connection and that its not faulty
have you tried to see it in the device manager
control panel admistrive tools,computer management,device manager you could see a yellow question mark? right click to reinstall drivers or in the device manager scroll to disk drives + to expand right click on the drive select properties then select enable this device from the drop down list you can also select the driver to update,rollback,uninstall also under policies optimize for quick removal,optimize for performance,restore defaults hope this helps

Hi julle_165.

Based on the information you have provided, it seems that the issue is caused by the Skype Application.

However, you may resolve this issue by performing the below steps.

1) Open the Skype Application and click on the "Options".
2) Then, click on "General and Audio Settings".
3) Then, in each of the three fields make sure you specify exactly which Sound Device you want to use.
4) Then, make sure that you do not select the ""Windows Default Device" option.
5) Click on the down arrow and find the Device you want.
6) Then, click on the "Save" option.
7) This should retain the Device settings which you have selected.
8) But, if you insert a new Sound Device into the Windows Operating System, it sometimes changes the settings to the new Device every time you insert it.
9) Just keep checking there that it is set on the device you want.

Performing the above steps should resolve the issue.

Hope this helps.

Please feel free to contact for further information and assistance.

first try reinstalling the driver of your external audio device, but first uninstall it.

Also check the device itself it may have faults like shorts and the like causing the laptop o protect and restart.

http://www.youtube.com/watch?v=GtCJ-nSCjvM
watch this video ok
now you may need the serial of that program here we go
DS-G06E8E90FA4D05C122D0E0501000G0

this is product is not useful for vista premium. you can use it in desktop. it work propeerly.

The ada800 gives out 8 channels of ADAT, the edirol UA-25 are only stereo opticals and not compatible with the ADA8000 as it does not have any adat inputs or outputs.
Hope this helps