20 Most Recent
HP PSC 2355 All-In-One InkJet Printer - Page 9 Questions & Answers
When trying to copy I get error code 0x088052c22
Hi there,
To start with i would recommend checking out this HP printers page and try the solution that they recommend. if this fails then your best bet would be to take this product to your local computer service center for servicing.
All the best :)
I have a HP PSC 2355 all-in-one. When I try to
Could be the main paper feed tire is glazed, worn out, or dried out.
Can be cleaned with a lint free cloth and simple green(alcohol dries the rubber out if used), scrub well with cloth then dry off you will find it will work well if glazed, or dried out. Of course if it is worn out the economics of the parts and labor would suggest replacement of the unit as this is not one of the more expensive units. In todays world the big box stores are selling for $38.00 per unit - hardly worth working on them when that is the cost of replacement. Good Luck.
mps4
Says paper jam and there
It is possible that even though there are no full sheets of paper jamming the printer that some torn bits have been left behind. You need to make sure that cleaning is complete.
Visit this site for full details:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00212225&tmp_task=solveCategory&lc=en&dlc=en&cc=us&site=null&lang=en&product=422000&key=null
Preventing paper jams
The following recommendations can help prevent recurring paper jams in your HP product.
-
Before loading paper in the tray, hold the stack of paper, and then tap the bottom edge on a flat surface so that the stack is even on all sides.
-
Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray.
CAUTION:
Do not force the paper to move too far forward in the tray.
-
Do not overload the tray with paper.
-
Only add paper to the tray when the product is not printing.
-
Make sure the HP product supports the paper type. See the documentation that came with the HP product for more information.
-
Do not print on paper with paper clips or staples attached.
-
Do not use paper that is bent, torn, dusty, damp, wrinkled, curled, or paper that does not lie flat.
-
Use only one type of paper at a time. Do not mix different types, weights, or sizes of paper.
-
Do not use paper that is too thin, too thick, or too glossy for the product.
Cause
The following factors can cause paper jams:
-
Paper loaded incorrectly in the paper tray.
-
Damaged or dirty paper rollers.
-
Torn, wrinkled, or damp paper loaded in the paper tray.
-
The rear access door or two-sided printing accessory (duplexer) might not be closed or is not locked into place.
-
Paper was added to a stack already in the tray while the HP product was printing.
-
The tray contains more than one type of paper.
-
The paper is jammed inside the HP product where you cannot see it.
-
An obstruction is blocking the paper path.
-
Torn pieces of paper from a previous jam are stuck in the product.
-
The tray is too full.
-
If printing on an envelope, the edges of the envelope are bent.
I hope thihs is helpful.
My PSC 2355 is unresponsive,
Hi,
Step 1
1. Disconnect the power cord from back of printer ( when the printer is on)
2. Wait for 10 seconds and connect it back
3. Once the printer is up, try to turn off and turn on, it should work.
If this does not work,
Step 2
1. Disconnect the power cord from back of printer ( when the printer is on)
2. Wait for 10 seconds
3. While holding the power and cancel button on printer, connect the cord back.
It should work fine.
* Please rate this solution with Thumbs up and comment to help us improve providing support
Not finding what you are looking for?
