20 Most Recent HP PSC 2410 All-In-One InkJet Printer - Page 5 Questions & Answers

Hi debbiewinkle
Disconnect your device . Delete and reinstall full software ( make sure it's not basic ) . Reboot pc . Reconnect printer .
Best regards,
fanaudi .

If you read the manual you will see that the unit will read SD cards, however the high caacity cards (SDHC) are not in the compatibility chart!

Welcome to Fixya.

You can try the following to remedy this problem as I had experienced it myself and was able to resolve it through the following means :

• Remove the top lid, unscrew the 5 screws, 2 on the left, 1 on the top (under the lid), and 2 more hidden under the grey board which can be remove with caution.
• Once opened, clean up the glass with some special clean-up liquid and dry. Clean-up the white square also under the lid.

Put the pieces back together carefully and try printing out.

Hope this helps, Thanks for using Fixya.

Navigate to the Windows control panel and double click Printers and Faxes. Now right click on your printer and select Printing Preferences.
Then click the quality tab and select either Standard or draft.
Click apply and Ok.
Check each print for the desired, quality over speed trade off.

Take care!
damnor01

This means turn the printer off, wait a few seconds then turn it back on again

During printing, the HP product makes unusual or loud noises. You might describe the noise as grinding, squeaking, or screeching.

Step one: Clean the rollers in the back of the product
1. Disconnect the power cord from the back of the product.
2. On the back of the product, find the rear door.
3. Squeeze the tab or tabs on the rear door, and then pull the rear door toward you to remove it.
4. Open the rear door on newer Photosmart, Officejet, or PSC productsInside the back of the product, rotate the paper rollers with your fingers to make sure that they can turn freely.
5. Rotate the rollers located on the inside of the rear door to make sure that they can turn freely.
6. Remove any torn pieces or scraps of paper that you can see.
7. Dampen a clean, lint-free cloth or swab with distilled water, and then wipe the paper rollers inside the product and on the inside of the rear door clean. Rotate the paper rollers with your fingers to clean all the way around them.
8. Reattach the rear door. Make sure that it snaps into place.
Step two: Clean the rollers in the front of the product
1. Lift the cartridge access door to access the front paper rollers in the product.
   NOTE: On some Officejet models, you might need to close the document catcher. Then, look in through the front of the product to access the front paper rollers.
2. Inside the front of the product, rotate the paper rollers with your fingers to make sure that they can turn freely.
3. Remove any torn pieces or scraps of paper that you can see.
4. Dampen a clean, lint-free cloth or swab with distilled water, and then wipe the paper rollers clean. Rotate the paper rollers with your fingers to clean all the way around them.
Step three: Clean the small rollers Dampen a clean, lint-free cloth or swab with distilled water, and then wipe the small rollers, also called the pinch rollers, clean. The pinch rollers are the small metal rollers directly above the paper rollers. Rotate the pinch rollers with your fingers to clean all the way around them.
NOTE: Do not clean the carriage rod. Removing or damaging the lubrication on the carriage rod can cause the product to make more noise. Figure 9: Carriage rod Step four: Clean the cartridges
1. Connect the power cord to the back of the product, and then press the Power button ( ) to turn on the product.
2. Open the cartridge access door. Figure 11: Lift the cartridge access door on newer Officejet, Photosmart, and PSC products
3. When the carriage stops moving, disconnect the power cord from the back of the product.
4. Press down on each cartridge to release it from the carriage, and then pull it toward you out of its slot.
   NOTE: You might need to lift a cartridge latch before you can remove the cartridge from the product. Press down on each cartridge to release it
5. 1 - Tri-color cartridge 2 - Black cartridge
6. Dampen a clean, lint-free cloth or swab with distilled water, and then wipe any ink or debris from the copper-colored electrical contacts on the cartridge.
   CAUTION: Do not touch the ink nozzles or the electrical contacts with your fingers. This can result in clogs, ink failure, and bad electrical connections. Figure 13: Clean the copper-colored electrical contacts 1 - Electrical contacts 2 - Ink nozzles Figure 14: Do not touch the copper-colored electrical contacts or the ink nozzles Place the cartridges on a clean sheet of paper, with the nozzles facing up.
Step five: Clean the electrical contacts inside the product
1. Dampen a clean, lint-free cloth or swab with distilled water, and then wipe any ink or debris from the electrical contacts inside the carriage
2. Let the cartridges and carriage sit for 10 minutes to allow them to dry, or use a clean, dry swab to dry the contacts.
3. Slide each cartridge into its slot at a slight upward angle, and then press firmly until you hear the cartridge click into place.
   • Install the tri-color cartridge in the slot on the left.
   • Install the black cartridge in the slot on the right.
   I hope this helps you!
   

Go to this page courtesy of HP:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00808543&lc=en&dlc=en&cc=us&os=2100&product=303756&sw_lang=
According to HP's website the driver is located in Windows Vista 64. Go into the printers area and click on where it says "add a printer". It will be a local printer and then when it comes to the make and manufacturer. Choose them and if it prompts you for the vista cd then put it in so it can install the drivers for you.

There are different things to consider if your printer is not printing your document

1. Check if the printer is on
2. Check if the cable from your printer is properly connected to the tower or your pc.
3. Check if your ink cartridges are not empty ( note: most printers will not print if one of the ink cartridge is empty)
4. Check for the error message that appears on your screen every time that your printer fails to print the document ( note: this will help you isolate problem)
5. You can use this link to download the manual for your printer ( this include steps to check your printer settings )

http://h10025.www1.hp.com/ewfrf/wc/manualCategory?cc=us&lc=en&dlc=en&document=&product=303753

Hi

Please check your cartridge head i think some dust or paper small pieces in there, clean both of cartridge to thinner, and try again....

Good Luck

probably a simple alignment problem. Go into your maintenance section and there is an option to align . Run this and it should realign your printing. Hope this helps!

I had the same problem with my HP L7590 All In One. After trying a number of things to reset nothing worked. Then I tried this just as a last resort and it worked.
Insert the/a memory card( it will tell you that you can only use one card at a time).
With the card still in turn off the printer using the power button.
Wait for 30 seconds then turn power on again.
The screen should say reading card. So wait for it to finish reading and all should be fixed.
If this does not work, try again using a different card.
good luck
****
Send me Kudos if it works.

Have you installed any drivers?
If you have follow instruction below

Navigate to "control pannle"

Find "Printers" option (may be different; based on Windows Version)

Click on printer and open it.
If there is a list of printer jobs righ click on one and click "clear are jobs"

IF there is one job still stuck in the list you need to hit the clear or stop button on the printer.

If that dosen't remove the job you need to reboot the Computer.


#################

If the printer does not exist or the print driver was not installed

go to http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=228&lc=en&cc=us&dlc=en&sw_lang=&product=303753

Follow on-screen instructions

Select operating system and hit ok

Click the driver section

now click the one that reads
Basic Software and Driver

Then follow any instructions the install presents to you.

Did you try to Reset the printer?

1. Unplug the power cord from the back of the printer while the printer is on

2. Now press and OK and Cancel button at the same time

3. While holding them plug in the power cord

4. Release the buttons when the printer turns On

It will reset the printer and you will see the message on the LCD also.

If this also did not help then try another cartridge and if that also does not help then there may be hardware issue with the printer .

Though still let me know what happened

what are you trying to print? word or webpage? or 3rd party software?
are you connected thru usb cable?if yes try the utility below

HP Print Diagnostic Utility

Download the file here.Copy and Paste it in your browsers address bar then enter.

http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-91788-1&lc=en&dlc=en&cc=us&os=4063&product=2510767&sw_lang=

Can't Print? Print Jobs are Stuck in the Print Queue
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02205477&cc=us&lc=en&dlc=en&product=303753&tmp_track_link=ot_search



Hope I help you a bit.



Your's Truly,

Christian from HP

Say "Thanks" by clicking the thumb icon in the post that helped you.

Please click "YES" in solution that solves your problem as "was this helpful?"
(Although I am employed by HP, I am speaking for myself and not for HP)

Unplug the power cord from the back of the printer while its ON

now Press and Hold

Ok and Cancel button at the same time

While holding them plug in the power cord

Once the printer turns on release the buttons

You will see the Reset message on screen of your printer and in the process it will align the cartridges

make sure that youre using a regular line not dsl or voip line make sure youve connected it to the right port it should be line 1 connect the printer direct to the phoneline check settings "rings to answer" must be set to 3 ring you should have distinctive ring it must be set to all rings check fax speed it must medium then run a fax test all of these are under fax setting on your printer send fax tp 1800-hpfaxme,if recived a reply your good to go...otherwise call hp support...

Greetings welcome to Fixya.

Might I suggest downloading and installing the latest drivers for your HP Printer.
See my published guide entitled How to Install the latest drivers for Hewlett Packard Printer!!!

Be sure to connect the USB cable to both the computer and the Printer then turn on the Power. Try different USB ports on your computer/laptop.

Navigate to the Windows control panel and double click printers and faxes.
Click print test page on the bottom right of the box.
Also view the print que, right click on your printer and set it as the default printer.
Then in properties view the print que!

Also when you are printing in MS Word, click file print, then when the settings come up for the print ensure that your HP PSC 2410 All-In-One InkJet Printer is selected in the top most section of the box.

Tell me how it goes via comment!
Thanking you
damnor01

If you look through the printer maintenance functions of the printer folder in Windows, there should be an option to 'clean' the cartridges and their respective jets.

However, it's not recommended to do this too often, because just a few cleanings can deplete the ink in the cartridges.

If you have missing lines or jets aren't putting out ink across the whole printed page, then the cartridges may have to be replaced.

if your cartage is lo then clean crriage pcb if the problem is not solven the replace it