20 Most Recent Miele 30 in. KM443 Electric Cooktop - Page 2 Questions & Answers

Hello

Keep the air holes around the burners free of debris and grease by clearing out the holes with a thin piece of wire or a toothpick. Cleaning out the holes helps the ignitor light the cooktop

Listen for the clicking sound of the ignitor, then turn off the burner if you don't hear the clicking.

Turn the burner to the "Off" position, if you continue to hear the ignitor tick after you've lit the burner. Turn the burner back on to relight it. Ignitors normally make a brief series of electrical clicking sounds when you turn on the ignitors.

Let the ceramic igniter dry out if it has gotten wet and the burner won't ignite. If the igniter isn't wet, clear out the little holes in the burner by chipping out any blockage with a straightened paper clip.

Clean the electrodes if the burners still don't light. The electrode is in the burner base. Clean the metal part with a soft cloth. You can use emery board on the metal part but not the white ceramic part.

its very expensive...much better to but a new one...ceramic hob with knob control not the touch control...

It could be the switch. I have a handy video that shows what to check: HERE If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

60 amps and 220 volts

seeming like you forget how to lock off.
keep the lock icon pressed stronger and longer,until will hear a beep,then turn it on

as far i know it is normal if u put at high control after a sec,the sencor control is turn off then a sec again it open coz of the sensor, design the sensor for not overheating the hob.it is normal try to position the control in in not a max position.or the pot u use is exactly in the circle or bigger dont put a small one in the bigger hole of ur elctric hob.tnx

I have the same problem. i've been on the phone with Miele tech support. i'll let you know if i have any luck.

Finally I found the meaning of FE 31. FE31 means "control panel is dirty" or "some object is on the control panel" When error code FE31 appear on the control panel, clean the control panel area with clean wet paper towel or remove any object on the control panel. If you do not trust me, turn on the cooktop and put small piece of paper towel on control panel. You cannot see FE31 error code soon. Turn off the cooktop and remove the piece of paper towel, the error code EF31 will disappear.

It is a generic hardware error and should contain a number which pinpoints the fault. You will likely need a service call. https://www.google.com/search?q=Miele+KM5676+cooktop.+FE+error ..

It is not advisable to use a broken ceramic top.

It is a gas appliance and it is a Miele, so you need a registered gas technician to service it. In my experience, the spark igniters work on all burners. To clean the burners, remove them all and put them in a large saucepan. Add cold water and dish liquid, bring slowly to a simmer and turn off. When cold, rinse and scrub with a plastic pot brush, paying particular attention to holes and slots. This was a job we did in the restaurant every week. It is a good plan to do before you go to bed for the least disruption. The product specs says; Automatic re-ignition • Sealed burners • M Pro Dual Stacked Burner System So perhaps my hack won't work if they aren't removable. I found this video :>) https://blog.yaleappliance.com/new-miele-hr1124-30-inch-professional-gas-range ..

https://www.coolblue.nl/en/advice/errors-miele-induction-cooktops.html How do I unlock my Miele cooktop? Just under the lock light you should be able to press/hold with your thumb for about 5-15 seconds and it should reset. You may need to place your thumb directly over the lock light or just below it and hold it for that time. Just under the lock light you should be able to press/hold with your thumb for about 5-15 seconds and it should reset. You may need to place your thumb directly over the lock light or just below it and hold it for that time. If this doesn't unlock when you do this then you have a problem with the control board.

YOU HAVE THE RIGHT IDEA A PROFESSIONAL REPAIR SERVICEMAN

• Error code E13 error showing on display
• What causes an E13, E 13 error code on the Induction Cooktop control panel?
• Error code 13 on Induction Cooktop control panel

Cause:

• Universal OFF key failure

Troubleshooting:

1. If the controls are wet or water made contact with them, dry off the controls.
2. Turn off then back on to reset.
3. If the error persists, reset the unit at the circuit breaker.
4. Turn the unit back on to see if the error code cleared.

That will not matter

Miele cooktop induction KM 6350, 6380, 6382, 6383 dE mode
How to switch off demonstration mode
Press ‘power’ button on front and ‘lock’ bottom at same time until you get p5 mode displaying ( it is in programming) mode.
Then press top left to ‘0’, bottom left panel to ‘0’, then press right bottom panel to 9, then press on ‘power’ button to save. This should take it off demonstration mode.