20 Most Recent Miele Novotronic Premier 500 Front Load Washer - Page 5 Questions & Answers

Check if the drain hose is blocked. Check the wires aren't loose on the drain pump. If all that's ok you will need to replace the drain pump.

washing machine is un balance position ,.proper balance machine solve prob

Broken electronic as a result of worn shock absorbers. See www.youfixit.eu

Check sump hose

Mains off the wall, unplug. Shut your wall faucet and disconnect your hoses coming to the machine - at the machine end. Get an old tooth brush to clear out the dirt which may be blocking your inlet valve. If possible gently pry off the fine filters to clean well. Re-insert the filters carefully and re-connect, the hoses. Things shd be okay. Otherwise you just hv to change your inlet valve.Please click if helped, would help others.

Both lights flashing usually is caused by a water leak into the case of the machine which trips the float switch in the base. You can reset this by tipping the machine forwards at 45 degrees and allowing the water to drain out on to the floor. It will reset everything but if you still have a leak it will trip ou again due to the float switch. I had the same problem with the 2 red lights flashing, which was fixed by emptying the float tray as above. On further investigation I found that the door seal had rubbed on itself at the 6 o'clock position and had worn a small hole which was causing the water leak.To replace or repair the Door Seal you will need to remove the front panel.1. Turn power off and unplug machine after opening door.2. Remove the front panel lower kick plate by inserting a thin ruler between the kick plate and front panel about 4 inches from each end and lever down until it releases.3. Remove the 2 screws at the door lock switch on the front panel.4. With the kick plate removed you will see 2 screws at each lower edge of the front panel, remove these 4 screws.5. Remove the spring loaded band from around the edge of the door seal facing you and after that release the seal from the front panel and push in.6. Remove the hex bolt from the 6 o'clock position just below the door seal on the front panel.7. You should now be able to lower the front panel out of the locating pins and remove it.8. With front panel removed you will be able to remove the tensioning band which holds the door seal in place around the drum by undoing the screw at the right hand side of the band at the 3 o'clock position. It is accessible from above with a long bladed screwdriver. Take note of how far it is tensioned on the thread of the screw and try not to undo it all the way or you may lose the nut on the band.9. Once you have removed the band, slip the seal off the drum and slide the water outlet to the seal from the dispenser.10. When you replace the seal do not do the tensioning band up too tightly or you will hear it squeak when you spin the drum in either direction.11.Reassembly is the reverse of removal, taking care to put the door manual release strap through the inner slot in the front panel.I repaired my door seal with Silicone Sealant and loose weave fabric tape after rubbing it clean with alcohol as i didn't want to pay $100 for a new seal from Miele.

check the electrical outlet and, or, the circuit breaker to your washer

If the water flows though the inlet then the flow pressure should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Test a pressure switch: Click on : http://www.youtube.com/watch?v=HZZ2bDMspj8

Check this link to replace the inlet valve: http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

I have the same problem, try checking the water temperature, it seems that this light indicates a heating ciruit problem. The next step is to check continuity of heating element. These are readily available from meile and other suppliers/ aution site on web.

Your question is not very clear but I will try to help you. If you need the brushes for the electric motor need to be replaced, you can google parts replacements for your machine, or go to the Miele Company on line and request the parts for your particular model.