Top 20 Miele Novotronic Premier 500 Front Load Washer Questions & Answers

the only way to do this is to take the top off and push the drum to the rear of the machine and use a stubby screwdriver to loosen the two or only one of the metal clips that keep the flange in place retighten and bobs your uncle it should be done without an expensive engineer callout charge eric

in the user manual there should be a section on advancing the programs on and or in the section of trouble shooting I would take the water outlet pipe and lay it near the ground to drain the water out into a bucket and then as the machine is not plugged in you should be able to open the door in a not on position eric

Hi it seems that one of the machine motors have burnt out, normally its the waste water pump that has got debris stuck in it, unplug the mains lead and remove the water inlet pipe after turning off the water isolation tap pull out and tilt the machine to access the smaller of the two motors if necessary replace please get an electrician to check the motor for you and reconnect hers hoping this small bit of advice helps you cheers eric

Do you mean it blow the fuses in the house? Must be an electric problem with it. Something is overloading the unit perhaps electric shorting in a switch. Ask an electrician, that is safest if you do not have experience with electricity.

During rinse, water usually flows through the softener dispenser. The cup fills up and a small siphon tube triggers a siphon actionwhich pulls the softener and water into the washer. This siphon tube is probably blocked with crud. See if you can pull a small cap like part out of the softener dispenser area. Clean both the inside of the cap and the hole under it. This will allow the water to flow into washer instead of flooding.

Bearings are in bad shape ergo used up. Recycle it as repairing it is to expensive.

hope video link helps, check out pump draining problems press the helpful button How to Diagnose Washing Machine Drain and Pump Problems

Check door latch spin switch I’m happy to assist further over the phone at https://www.6ya.com/expert/howard_977676954994c5b2

Put a towel down in front of machine. Tilt machine forward. Water should run off the sensor plate and fix this problem.

If there's water underneath the machine, check drainage pump. Most likely gasket or simmering. If necessary replace pump (about $45,00).

Try checking the filter for a blockage or pump being jammed with a button , disconnect drain hose at sink hold a few feet off ground over a bucket should pump/ flow quite freely if not then check filter and pump. good luck

This may help. Miele Cosmos change the bearrings

On most dryers you can use a screw driver with a piece of cloth so you will not scratch it and pry up the top of the dryer. It will swing up and away or come off. Then feel for screws on the bottom of the dryer. You will need a offset screw driver to undo these or lay dryer on the side. There are also screws on the back. Pull the back away and off. Remove the belt remembering how it was threaded to the motor. Then lift up on the drum and pull out. If it is wore it will come right out. Unbolt the holder on the back of the dryer and the back of the drum. Replace and reassemble.

• Open the door
• Pull out the mains plug
• Remove the metal ring around the door opening seal (apply pointed pliers to stretch the spring beneath the door opening)
• Push back the seal from the front panel
• Loosen the two door opener screws
• Remove the plinth
• Remove the two outer upper screws behind the plinth
• Remove the bolt right underneath the door opening while supporting the front panel
• Gently lower the front panel and take it away

If the brushes are all right, then probably the electronic is defective. Check for our repair service at www.youfixit.eu.

the should be a ring around it that clips off so it can be taken off then replace with a new one and put the ring back on that holds it in place

Some tissues are more sensitive to shrinking than others. Some clothing cannot be machine washed or only at very low temperatures (hand warm). Especially woolen fabric will shrink even at 40 degrees. Be carefull with spinning at high RPM's. Always consult the label in the clothing:

3 dashes (or bars) in our Miele W1119 washer display. Beeping. All lights are off and machine is not working. Miele service call: the light bulb in the drum was loose! He pushed it back in and the machine worked fine again. This solution is nowhere to be found. Only in the service manual according to the service tech.

Check if there is a filter on the water inlet hose which could be dirty..Remove fill hose hold over sink/bucket check water flowing fleely if so then fit new solenoid Water valve...Good luck

Check if the drain hose is blocked. Check the wires aren't loose on the drain pump. If all that's ok you will need to replace the drain pump.

Just wanted to mention mine was retaining the fabric softener and skiping steps in the cycle and intake red light was flashing too. Once
I cleaned the draw and used a toothbrush to unblock the holes in the ceiling its working again perfectly. Miele Novatronic W 828.