Top 20 Frigidaire Refrigerator White Fridge & Freezer Handle Set - 5304485330 - Page 4 Questions & Answers

part number Frigidaire Plug #WCI-216502600 https://www.partselect.com/Models/GLFC2027FW6/

https://www.appliancepartspros.com/search.aspx?model=frs26zth

Ice Maker Is Frozen Up This ice maker repair is even easier. If your ice maker has frozen up, take the following steps to thaw it out: 1Unplug the refrigerator.Remove the ice bin from the refrigerator and remove any loose ice from the ice maker. 2Find the fill tube.This is awhite rubber-like hose that delivers water to the ice maker. Pull down the small metal clip off the housing that holds the fill tube (though not all ice makers have this clip). 3Warm the hoseand surrounding mechanism. To do this, you can train a hair dryer on the ice maker to melt any ice blocking the mechanism. But be very careful (sop up any dripping water with a rag) as electricity and water can present a serious risk of electrical shock. Also, be careful not to melt the plastic parts. 4If you don't want to use a hair dryer,you can soak the supply tubing with hot water, using a turkey baster and catching the overflow in the empty ice maker bin. In some cases, it may be easier to remove the ice maker than to thaw out the fill tube. On heat release ice makers You will want to check the heating element within the ice maker for continuity and a visual inspection of the board and conductors for burns and seizing, chared marks.How to Test the Ice Mold Heater There are two types of ice makers, those in which all of the parts can be individually replaced and those in which some of the parts are clustered together into a control module. To determine which model you have remove the outer face plate. If there is knob, pull it off first, then pry off the face plate with a small screwdriver. Modular units have holes in the module's face plate for test probes. If you see several holes, each marked with a letter, it is a modular unit. It is easier to work on this type of unit by first removing the entireicemakerfrom the freezer compartment. The unit is usually mounted to the freezer case by two or more screws. Remove the bottom screws first. While supporting the ice maker, remove the remaining top screws. Unplug the ice maker from the freezer cabinet if you have not already done so. Along the edge nearest the shutoff arm, a pin protrudes through the mounting plate . The arm pin has a spring under the mounting plate. Reduce the tension on the spring by moving the shutoff arm into the "on" position, down, against the ice maker. Test the heater for resistance using amultitester. Set the multitester to the ohms setting X1. Touch one probe to each of the two terminals (or wires). The reading should be in the range of 60 to 90 ohms. If you get a significantly different reading, such as zero or infinity, then the mold heater is bad and needs to be replaced. Conduct this test with the refrigerator unplugged. Test the moldheaterfor resistance using amultitester. Set the multitester to the ohms setting X1. Place one probe into the hole labeled "H" and the other probe into the hole labeled "L". The multitester should read in the range of 60 to 90 ohms. Also be sure to check and test water valve with a meter for continuity and voltage..( a full 120 and nothing less) And a visual inspection for any ice build up or blockage in tubing and flow line. Remember u may get a close circuit reading of continuity however it may still be bad in that it may remain constantly closed and water keeps flowing more than suppose to. Hence chunks of ice build up. : God is the reason I give you free advice so God is good! http://www.appliancerepair.net/refrigerator-repair-1.html

Are you calling the compressor condenser? My gallery side by side stopped cooling the refrigerator side and it was the control board under the refrigerator side. Also, just because the control board is new does not guarantee it is good. There are a lot of youtube videos on trouble shooting the Gallery. You might not have plugged in all the connectors when you changed the board, or maybe bent some pins.

it probably needs freon and only service people can do it right

Bad connection, faulty power supply, faulty door switch. etc etc etc.

Unplug and get a pair of needle nose pliers..grab metal end of bulb and remove..

is the water running into the unit check valve is open and check for clog

The defrost drain is clogged or the icemaker drain line is frozen

It uses the condensation to cool the coil. It is normal to not see any water

The filter supplied by the manufacturer.

Automatic defrost systems are better at reducing maintenance costs than fridges with a manual defrost system.

The wiresignal arm is located above the cube bin.

Check the temperture and make the freezer and fridge in the middle setting...wait 24 hours and see if that helps.

CALL YOUR LOCAL REPAIR SERVICE IT NEEDS TESTED WHICH WE CAN NOT DO

English only on Fixya Hi, I need to change the timer on a frigidaire part 134803600, but I don't know how to remove the knob. Any suggestions, thanks. https://translate.google.ca/?sl=en&tl=es&text=Videos%20are%20in%20this%20link&op=translate Videos https://www.google.com/search?q=frigidaire+replace+timer+134803600 ..

neither you or we can add the needed gas so call a repair service

sad to tell you but only a local repair service will be able to figure it out for you

Typically this is a customer alert warning - could be high temperature or open/ajar door or something else. Consult the owner's manual (can often be downloaded from factory website with model) and check the troubleshooting guide near the rear of that manual. With no model number there is no more specific answer.

This has nothing to do with the filter. Just a coincidence. Here is what Frigidaire says: Frigidaire Refrigerator Error Code = 4 Condition = Fridge and the control board goes through cycles but does not detect a damper connection Repair or Check = Check air damper Parts Needed = Air damper