Top 20
Hotpoint Aquarius WMA42 Front Load Washer - Page 8 Questions & Answers
Hello haw to clean a filter of this washer?
The filter is located within the sump at he bottom middle of lower drum.Hose other end connects to pump.Remove lip at drum end look in and withdraw filter from sump hose to clean. Note how it comes out ensure refitted same way, water test machine......hey bobs yer uncle
6/25/2010 10:44:05 AM •
Hotpoint...
•
180 views • 0 helpful votes
Washing covered in dirty marks
It sounds as if a bearing seal was defective when it left the factory and is allowing lubricant to bleed out; I would consider this a warranty item and if the company doesn't care to make it right, file a complaint with the local BBB relating to the dealer where you bought it and nationally against the company itself.
Maybe they don't want this stain on their reputation but this is another reason to avoid US manufacturers.
5/25/2010 9:33:10 PM •
Hotpoint...
•
371 views • 1 helpful votes
How to replace bearings in hotpoint washing
Hello,It's fairly straight forward,not easy though.The facial comes off(take the dispenser out and remove the four screws), front of the machine comes off (3 screws at the bottom and 3 behind the facial,the outer tub front comes off.)The pulley on the rear comes off,the inner drum can be knocked through.This gives you access to the bearings and bearing seal,not the easiest to get out.A lot of the time the outer race is left behind from the front bearing and it's a nightmare to get out.Hotpoint use a special bearing tool,get yourself a spider and bearing kit as well as a new tub seal.
Thanks
5/30/2010 8:47:57 AM •
Hotpoint...
•
323 views • 0 helpful votes
Not going on fast spin?
These machines have a max load system, please try it empty, and tell me if it still has the problem.
8/3/2010 1:19:37 PM •
Hotpoint...
•
48 views • 0 helpful votes
Flooded the kitchen, spinning but not pumping out
Usually an indication that something is caught in the pump inlet. You will have to remove the hoses and see if its a sock or some other small treasure..
Please rate my help++++Thanks for using FIXYA
6/3/2010 6:01:45 AM •
Hotpoint...
•
216 views • 3 helpful votes
Hotpoint Aquarius WM62 bearing noise
Hello,remove all the surround screws from around the door glass then gently lever the 2 halves apart,remove the old hinge,and re mount the new one along with the plastic bearings refit the screws,refit the door to the front cabinet.
Thanks
5/23/2010 8:05:08 AM •
Hotpoint...
•
259 views • 0 helpful votes
How do i fit a new belt in the washing machine...
Hello,unplug appliance, remove lid and back plate, place belt on motor and
carefully on drum pulley, turn pulley to pull belt onto its, its quite
tight to do but is possible, watch out for trapping your fingers.
Thanks
5/21/2010 9:27:33 PM •
Hotpoint...
•
236 views • 0 helpful votes
Washing machine wont spin and is full of water and
-
1
A
washing machine won't spin if the water can't drain. Check hoses for
any kinks or clogs that may prevent the water from draining. If a hose
has kinks, try to straighten out the kinked hose. If it can't be
straighten sufficiently, replace the hose. If hoses are not kinked,
check for clogged hoses. This can be done by using the screwdrivers to
remove the hoses and looking for clogs or running a water hose through
the clogged hose to remove the clog. Use the rags and bucket to clean
up the water that comes out of the hoses when they are disconnected.
Once the clog is cleared, put the drain hose back into place. The
washer should drain and spin now if a clogged or kinked hose was the
problem.
-
2
If
the washer still won't drain or spin, check to see if the lid is not
closing all the way or if the lid switch is not clicking into place.
Close the lid and make sure that it closes all the way down. When the
lid closes, the lid switch should click. If there is no clicking sound,
then the switch may need to be replaced. Follow manufacturer's
directions for replacing the switch. If the lid does not close all the
way, visually check for signs that the lid is bent. If bent, try to
bend it back into place.
-
3
Loose
or broken belts could also prevent a washing machine from draining or
spinning. Pull the washer away from the wall and, using the
screwdrivers and wrenches, remove the back panel. Using the flashlight,
visually check for any broken or loose belts. Replace any broken or
loose belts. Although replacing washing machine belts is difficult,
anyone who has replaced belts on a car, lawn mower or even a bicycle
chain should be able to accomplish the task.
-
4
Another
possibility for a washing machine to not spin or drain is the pump.
With the back panel still off the washer, check the pump with the
voltmeter to ensure that the pump is getting power. If the washer is
getting power, turn on the washer and listen to find out if the pump is
running but the water is still not draining. It may be necessary to
remove the pump and clean it or to replace the pump with a new one.
Once the pump is replaced, turn on the washer to determine if it will
now drain and spin.
-
5
If
all of the above steps fail to produce a washing machine that drains or
spins, then it is time to call a professional repairman. Use the
screwdrivers and wrenches to replace the panel on the washer and push
it back against the wall.
5/31/2010 9:40:09 PM •
Hotpoint...
•
156 views • 1 helpful votes
Bra wire stuck in drum
Tricky one there. Anyway, best way to tackle that is to locate the heating element and remove it. The bra cup spring normally locates itself against the element. Look in the element cavity with a torch and you will normally find it while slowly turning the drum. Use a long type of extraction pliers and remove.
5/25/2010 4:14:58 PM •
Hotpoint...
•
178 views • 2 helpful votes
Wash machine pump doesnt work
Hiya,
some machines have a filter at the front of the machine it will be right down the bottom behind the trim this trim normally just pulls to open & if so you will see a small circle if you unscrew that some water will come out & if blocked will have some stuff in that you can remove,
Hope this helps
4/20/2010 8:00:59 PM •
Hotpoint...
•
389 views • 0 helpful votes
Dishwasher is not washing dishes properly . cloudy
The problem is hard water. www.dishwasherfilter.com has a product to solve this problem once and for all. It filters the water going into your dishwasher and removes the hard minerals that leave those spots. It is very affordable and even has a money back guarantee. You will love the way your dishes look with this product.
6/2/2010 9:36:53 AM •
Hotpoint...
•
105 views • 1 helpful votes
H20 ERROR SPIN DRYING
The error indicates a problem with the incoming water supply.
Check for restricted or kinked inlet hose/s, check that tap/s are fully turned on and that you have adequate water pressure.
3/27/2010 3:55:47 PM •
Hotpoint...
•
614 views • 1 helpful votes
Hotpoint drive belt
un plug appliance, remove lid and back plate, place belt on motor and carefully on drum pully, turn pully to pull belt onto its, its quite tight to do but is possible, watch out for trapping your fingers.
4/7/2010 8:02:52 PM •
Hotpoint...
•
380 views • 0 helpful votes
Machine will not empty
Remove lower rear cover of washer.
Remove large black hose from bottom of drum.and remove and clean plastic filter inside hose.
Refit and test.
5/9/2010 2:54:53 PM •
Hotpoint...
•
155 views • 2 helpful votes
Drum not going round
Hi Friend,
welcome to fixya....
may be the drum belt is the fault, Here are some possible causes of a washing machine belt coming off :-
1.The drum pulley is loose
2.The drum bearings have gone (collapsed) causing the drum pulley to wobble
3.The drive belt was to slack
4.A motor fixing bolt or bracket securing the motor to the tub has broken or come loose
5.Water has got onto the belt causing slippage
6.An obstruction or item of clothing temporarily jammed the drum causing the belt to spin off ,,,,,,,,,,,,
first check whether it is hard to turn the drum if not then check the above situations,,,ok
if you think that i helped you please rate it\\\\\\\\
thank u...
4/3/2010 3:06:07 PM •
Hotpoint...
•
308 views • 0 helpful votes
Not finding what you are looking for?