Top 20
Hotpoint Aquarius WD640 Front Load Washer/Dryer Questions & Answers
Hi i have wd640g hotpoint
Check all thermostats , check to be sure you have 220 volts coming into the machine. Use ohm meter & check from heater element to the heater case or cabinet to see if the element is grounded. Positive to element & Negative to case should show no ohms if it does it is shorted. Also heater circuit runs through a centrifical switch on the motor
so if the motor quits the heater shuts down so you don't have a fire. When the motor is not running the fan stops.
You could check this switch but it don't happen very often. check this switch last. Hope this will help you
2/1/2018 11:06:03 PM •
Hotpoint...
•
140 views • 0 helpful votes
Hello I have a Hotpoint WF340 washing machine. It
go to the parts website for Hotpoint for price or Google the part number and someone will post it for sale.
Try going to You-Tube for instruction video on replacing.
If it is still under warranty, call mfg or warranty company.
11/16/2017 4:54:03 AM •
Hotpoint...
•
467 views • 0 helpful votes
Underwire stuck in hotpoint WMD 940
i can try to help you with this problem. if you pop the cap off the top of the agitator you will see a nut, once you take the nut off you should be able to jiggle the agitator in an upward motion to remove it then retrieve your wire and gently slide agitator back on so as not to ruin the splines if there are any. good luck
9/29/2017 2:36:03 PM •
Hotpoint...
•
186 views • 0 helpful votes
I have a Hotpint Aquarius Washer/Dryer model
you could have a broken pipe on the filler or the seal has gone on the drum you would need to have a look, either way they are easy to fix or replace. drain pipe can leak if the pipe has come off the pump also check this but you will need to remove the case to get to look, always unplug the washer before touching any screws, remove case and look at the pipes and make sure they are seated in the right place.
9/9/2017 12:27:03 AM •
Hotpoint...
•
169 views • 0 helpful votes
Why is there no power?
Hotpoint red led flashes Washing Machines Questions ...
www.fixya.com > Forum > Tags > red led flashes > Washing Machines
Hotpoint washing machines red led flashes related questions and answers. ... then off When i turn on the washing machine - Hotpoint wf640p - the LED display flashes all the 8s (so ... Question about Aquarius WD640 Front Load Washer/Dryer.
10/27/2015 12:18:01 AM •
Hotpoint...
•
286 views • 0 helpful votes
What is it when flashing f11 on washer
F11 is a pump fault. Probably a blockage in the sump. From what I recall, there is no access to the pump at the front of the machine on this model, but if you go to the back nd remove the panal at the bottom, you will see the rubber sump that hangs from the bottom of the drum. It is usually held on by either a large jobilee clip or a squeeze clip. Undo this and pull off the sump. Inside you will find what looks like a basketball hoop woth a ping pong ball in it (It's a water save device)> Chances are that this is blocked with debris. Clean it out and reassemble and all will be well.
10/14/2015 1:30:39 PM •
Hotpoint...
•
97 views • 0 helpful votes
How to reset machine
You can't "Reset it" as such, you need to fix the fault. Is this the F11 issue you reported before, or another problem?
7/28/2015 9:06:57 AM •
Hotpoint...
•
172 views • 0 helpful votes
Tumble dryer not heating
If the fan in the aluminium bit on top sticks then the thermal fuse at the front blows
6/29/2015 9:29:00 AM •
Hotpoint...
•
155 views • 0 helpful votes
How do i unlock the door as it will not open
As you know, the door is locked while the machine is working.
The most likely cause of your problem is that the 'interlock' has malfunctioned and needs to be replaced.
The problem is to get the door open.
Try to remember which way the latch hooks into the interlock.
It may be that a flexible kitchen knife slid behind the door can release the doorlock, or a length of thin strong string passed around the door and pulled towards the hinge side will release the latch.
N.B. Be careful not to damage the seal....!
If these actions don't work it would be best to call a technician to release the interlock from the inside of the machine and replace the interlock, which can be a slightly complicated job..
Good luck.
Nomess
3/8/2015 7:54:25 PM •
Hotpoint...
•
92 views • 0 helpful votes
Bypass the timer switch
Fit new timer switch to avoid heating if you bypass it it will go flat out and burn out the element.
11/15/2014 8:29:59 PM •
Hotpoint...
•
925 views • 0 helpful votes
Not finding what you are looking for?