Top 20
Hotpoint Aquarius WF000 Front Load Washer Questions & Answers
My washing machine wont start.
I have a hotpoint washing machine if I start the machine the water it's working after filling up the water the basket doesn't spin
12/11/2015 4:26:09 PM •
Hotpoint...
•
245 views • 0 helpful votes
Hotpoint not drying clothes
Check the vent hose and the vent in the house for dryer lint. Excessive amounts will block airflow and the dryer senses that and shuts off the heat to prevent a fire.
10/14/2014 9:45:32 PM •
Hotpoint...
•
72 views • 0 helpful votes
How do I remove the clips from the pump
I found it easier to hold one part with a Pointy nosed pliers and push the plastic grip out the side of the clip.
As it is plastic it just ratchets back into place.
7/14/2014 11:13:16 AM •
Hotpoint...
•
63 views • 0 helpful votes
My Wf000 door Locked is flashing, machine will not lock?
You can try this.
Switch off the washing machine at the mains, unplug it and leave it unplugged for about 5 minutes.
Plug it back in and see if it will work.
If it doesn't work you may need to buy a new door lock mechanism. The door lock has some electronics which can fail sometimes. You can buy the door lock on the internet for about twenty pounds and can do it yourself if you are fairly handy. There are also videos explaining how to do it on YouTube.
It worked for me.
Good luck
6/17/2014 12:10:17 PM •
Hotpoint...
•
45 views • 0 helpful votes
Leak from front
You take off the top to get into the machine, there are usually screws at rear top holding top panel on.
That said the most likely culprit is the pump which you get to from underneath, followed by the door seal, which you should inspect carefully for very small holes. My guess is the pump, have you checked the filter is clear?
5/16/2014 1:36:33 PM •
Hotpoint...
•
33 views • 0 helpful votes
Water not pumping out of machine-zanusi aquarius wf000
1. Check that the water tube is properly fixed
2. The tap is on
3. The program is on
If you hear a humm sound without water means that the valve is open but is closed before that.
If no humm is heard then the valve could be broken.
4/2/2014 9:33:09 PM •
Hotpoint...
•
32 views • 0 helpful votes
Wf541 problems
if you mean the mains switch power this is available to buy on its own fairly easy to do,only four wires are connected to it.
11/6/2013 2:35:46 PM •
Hotpoint...
•
75 views • 0 helpful votes
Led key light flashes on my mwa64 hotpoint washer
Possible that the INLET and OUTLET - DRAIN filters are clogged or there is limited action. Remove and clean inlet and drain filters.Also check on the connectors from the panel, reset all connections.
1/17/2013 1:54:30 AM •
Hotpoint...
•
71 views • 0 helpful votes
Where is the filter in washing machine
Start by turning off the hot and cold water faucets that are connected to your washing machine. This will stop water from running into your washer so you can disconnect your water inlets without flooding the house! To relieve any built-up water pressure, pull the knob out on your washer that starts the washing cycle for just a few seconds.
Now it's time to unplug and disconnect your washing machine. First, unplug your washer from the electrical outlet. Next, use a pair of pliers to unscrew the hose fittings on the back of the washing machine. There will likely be some water left in the hoses, so you will want to have a hose or a bucket handy in order to catch and clean up any spillage.
Now it's time to break out the water-resistant vacuum. Place the vacuum over each water inlet. As you turn on the vacuum, tap on the inlet a little with a plier in order to free any debris or sediment that may have lodged in it. Continue vacuuming until the inlet is clear, then repeat on the second water inlet.
Now that you're done clearing out the filters, it's time to reconnect your washer. Using your pliers, reconnect the correct hose to its inlet and make sure to tighten them properly. Don't forget to double-check to see if there are any leaks. If you find any, re-tighten accordingly. After that, all you have to do is plug your washer back into the outlet and you're ready to go. You've successful cleaned out your washing machine filter!
8/5/2012 6:29:54 PM •
Hotpoint...
•
93 views • 0 helpful votes
Will not drain the water
The most common cause is a foreign object caught in the pump keeping the little impeller from spinning. Take off the pump hose and make sure it is not plugged.
3/14/2012 8:10:47 PM •
Hotpoint...
•
42 views • 0 helpful votes
Not finding what you are looking for?