Top 20 Brother MFC-8870dw Wireless Multifunction Laser Printer Questions & Answers

10cm means it's caused by a large roller. The only roller large enough for that would be in the drum. Replace your drum and it should clear up, the model number of the drum is DR520.

The 'OK' button is the enter button for data entry purposes. When in settings pressing ok will accept any setting you have changed.

Sir/madam Please Follow the Video http://www.youtube.com/watch?v=xig75RXA5qc For Your Printer Brother Troubleshoot Or Follow Us For On Brother Printer Support

first, Enable the WIFI on you printer, then install the driver in you computer, to option to choose before you finish the installation, First Select your connection, Choose Wireless Connection, not USB Cable

There are shorter way but are machine dependent, this will work for all...http://tricks-collections.com/reset-all-models-of-brother-printers/

How do I connect a Brother MFC 7840W printer to a Bell Network. Every time I try to connect, I get a connection NG message on the printer. Any help would be greatly appreciated

Laser printers do not use a printhead.When the toner runs out you need to get a new toner cartridge which includes the print drum.You lift up the cover to reveal the toner cartridge, grab the cartridge and pull it out towards the front of the printer.Reverse this procedure to insert the new toner cartridge.

Try:Log into wifi router D-Link dir-615. Change: security mode to WPA-Personal, WPA Mode to WPA Only, and Cipher Type to TKIP. Then try connecting again.

Ok, here's a video of someone removing their toner.
Ignore his tip about how to get hundreds more pages out of the toner...it'll probably just make you cry anyways.

http://welcome.solutions.brother.com/bsc/public/us/us/en/dlf/download_top.html?reg=us&c=us&lang=en&prod=mfc8870dw_us_eu
From here select your operating system and language, the page will provide you with download links for the drivers.

To be able to set up wireless printer configuration, there are three basic items that you need to have. They are a high-speed broadband Internet connection (with modem), a high speed wireless router and wireless network adaptors. These three items will be used in setting up the wireless printer. Assuming that there is already an existing network in the home or office space, then all that is needed to do to make the printer available in the network through the operating system's networking wizard. If not, then the network must first be established, only then the printer will be made available through that network.

Connect the printer with a USB cord to the computer. Switch off the printer and install the driver in to your computer , during installation the software will tell you to switch-on the . Do so and finish the installation .
This is the procedure to connect the printer with your computer.

buy a new printer:)

I've got the same issue, but with a Linksys WRT54GL running dd-wrt. Haven't found a fix yet, but if I do, I'll come back to post it ...

There are two jacks side-by-side. Be sure the phone line is plugged into the one marked LINE, not the EXT. jack, which is for extension phones or answering machines. OK, it's not that. Don't be mad - we had to check.
Most of the telephone circuitry is on the Main Board, but first the line is fed though a Network Control Unit, part number LG5857001. That NCU board is fairly cheap, but you don't know whether it's the problem until you replace it. NCU Board problems are often visible with a good magnifier: broken solder joints & stuff. Problems on the Main Board (part no. LT0226001) are more common and more expensive - maybe more expensive than replacing the machine.
Brother has a one-year warranty on these. If it's just past that, you might still be able to talk them into sending a Work Order to your nearest Brother servicer to do it free.

If there is not something jammed in the paper path, like a paper clip or staple, check the left rear hinge for the scanner, when it breaks it holds the rear side up and paper jams...

It means the drum has nearly reached the end of it's useful life, just a warning before it says it is all used up. If quality is still good you can open the front door and press the menu or options key and tell it it's a new drum and keep printing until the print quality fades.

I had same issue just now. picked printer up 1 inch and dropped it. Then shook lightly it as I sent a print job to it, and it came back to life.

Sounds like you will need to purchase a new fuser for your Laser printer, have you tried to take the fuser out and place it back into the machine to see if it would reset or still function with the laser?

If it doesn't work, then you will have to replace the fuser, can you send me the brand and model and or part number from the old fuser and I can look it up for you.

With in 2 seconds you have to hit Menu,*,2,8,6,4
Continue even though you hear the 3 beeps.
When it does into maint mode press 88
That is parts counter reset
Scroll to the part and hit ok.
Press 99 to exit Maint mode