I just got a used quinny Sx stroller I can't figure out how to close/ fold it down.
Posted by mnbolduc on
In the middle of the underneath of the pushing handle, below where the hand brake lever is there should be a button. If there is, this is what you do.
1) put the foot brake on so the rear wheels wont turn.
2) unclip the clips on the frame that allow you to adjust the height of the pushing handle, they open up, and leave them open, like this the handle you push the buggy with should slide up and down.
3) pull this handle out to its tallest position
4) Hold the handle and press the button mentioned at the start in and hold it in
5) Then quite quickly push the handle down as though you were either pushing it to lower its pushing height, or shoving it away in a temper. It needs to be a firm and quick movement.
Ta da!! After a couple of tries it should click and fold up.
I hope this helps.
Posted on May 13, 2009
i have brought a quinny footmuff to fit my quinny buzz and want to no the fitting instructions to install it. thankyou
Posted by nat89 on
hey it took me a while to figure it out, at the top of the padded shoulder straps at the back if you feel with your fingers you will find a popper fastening you have to pull it so that it comes away then you should be able to find that the harness is attatched by a loop, take that off and then with the harness unattatched you can thread the slits of the footmuff through and then reattatch it all including the padded shoulder straps, i took mine apart today because my daughter has outgrown the comfort cushion so i took it off after realising there was a bigger seat unit undernath it i bet not alot of people know you can do this, anyhow, by adding the footmuff it makes it alot more padded and cosyier hope that helps!
Posted on Apr 07, 2008
My quinny buzz front wheel keeps getting stuck half way and i end up trying to push the chair with the front wheel sideways which is impossible. i have been advised to clean the front wheel out as it gets dirt and grime but i have no idea how to do this. i have taken the front wheel off but that is as far i get. please help.
Posted by zgilling on
First remove the front wheel assembly from the pushchair by pressing in the two buttons on the sides and pulling it out.
Now look more closely at the assembly - on one side, just where it bends at an angle you will find a small hole, a couple of millimetres across. Take a small screwdriver or some other thin object and push it into the hole a little way, which presses a metal catch inwards, releasing the swivel assembly. While continuing to push this in pull the swivel assembly apart - grasp the wheels in one hand and the L-shaped plastic housing in the other and pull them apart.
Now clean all the surfaces with a piece of strong cloth.
When all the surfaces are very clean, take a can of TEFLON SPRAY and spray it onto all surfaces that rub against each other, before reassembling the wheel unit. Silicon grease is a cheaper alternative, but the teflon spray is supposed to be the best for lubricating all moving parts on the Buzz. Whatever you do, don't use WD40.
Hope this helps! Dan.
Posted on Feb 27, 2009
i have a split in the foam handle - what does anyone recommend to patch it up or can you get replacements? many thanks
Posted by Anonymous... on
I need front replacement wheels for quinny buzz 3 wagtail design pushchair
Posted by nanby14 on
If you are in the UK, the following website is much cheaper than the others listed...
Posted on Jul 14, 2009
Hi I have a quinny buzz with broken cable in the handle, I have managed to get a replacement handle but does anyone know how you get the original handle off so I can put the new handle on ?? thanks
Posted by patricia... on
GO TO WWW.,BUGGYPITSTOP.CO.UK THEY DO REPAIRS TO BUZZ'S AND THEY HAVE SPARE PARTS IF YOU REQIRE THEM
Posted on Jan 09, 2010
I am wanting to buy a replacement seat for my quinny buzz as it is looking a bit grubby. I can't seem to find anywhere that sells them. Please can you tell me where you bought yours and how much it was? Thanks xx
Posted by scrubnurse on
I have a quinny buzz and my pareents have forced the mechanism to remove the seat when they were babysitting. I have managed to find most of the parts that came out when it broke and put them back together, but the white plastic part inside the hole where we insert the seat is missing (the plastic part is necessary to adjust the seat and set the incline. It is round, white and about the size of a quarter, with 4 little rectangle bits sticking out) Is this replaceable? thanks for your help
Posted by marieh... on
Hi - Please can you visit the Quinny page and use the 'contact us' tab for your enquiry to be directed to the customer care team in your country who can help you. http://www.quinny.com/international
Posted on Jun 05, 2017
One of my Quinny Buzz Tires are flat. It is difficult to attach an air pump because of how the tip is located close to the tire. Is there anyway to fill up the tire before having to replace it?
Posted by jnalderman on
You need to either have a new inner tube put in it or you can try adding a flat repair gel in the tube to fix the leak. You can get what they call "Green Slime" their are other brands also available under different names but this is most common. It can be purchased at Walmart, Home Depot, Ace Hardware and Auto Parts Stores. This is easy to pump into the tube valve stem without removing the tube or wheel and should fix any holes or leaks on it. Then just pump it up and you should be ready to go.
Hopes this was helpful, DutchTexan
Posted on Nov 06, 2009
Last year a friend of mine bought the Quinny Speedi SX for my little newborn. As my child has grown (13 mo), she now wants to sit fully upright. I can not figure how to make the seat go up. I have seen the manual and how the backrest works but still it doesn't go FULLY upright.Do you suggest anything? TIA Evangelia from Greece
Posted by Eva Eva on
i got fed up of my little one getting annoyed because he wanted to sit up and the buggy wouldnt !! so i brought a luggage strap fixed it behind the seat around frame and cliped it together,seat goes upright, you can still vary the incline of the seat and take off when not needed! PROBLEM SOLVED! XX
Posted on Aug 16, 2009
346 questions posted
Usually answered in minutes!
Step 2: Please assign your manual to a product: