Hoover H130E Front Load Washer - Answered Questions & Fixed issues
Can't open the door timers saver & 1200 spin lights flash
There is a known problem with these washers whereby a small electrical current 'leak' from the heater element causes the machine to think it still has water in it.
Disconnect the wires on the heater (tape them up or otherwise make safe) then run a cycle to verify that part as the problem.
1/31/2018 5:43:41 AM •
Hoover H130E...
•
Answered
on Jan 31, 2018
•
217 views
The door hinge has snapped is it easy to take off
Two screws hold the hinge to the frontplate of the machine which goes into a threaded nut welded to the panel (torque to 30/40 foot pounds or relatively snug).. just remove the screws and raise the hinge and pull forward..(keyhole slotted on)... then reverse to attach the new door...
6/6/2011 6:17:14 PM •
Hoover H130E...
•
Answered
on Jun 06, 2011
•
257 views
I have a h130 front
Hi from retired Englishman in SW France,
Here are my complete guidance notes for checking both the drain motor filter and the drain motor. The bit about checking the motor is near the end ;-0)
-------------------------------------
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!) and most are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play!
REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT!
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning!
Good luck!
John C
4/9/2011 9:09:29 PM •
Hoover H130E...
•
Answered
on Apr 09, 2011
•
80 views
The washer wont spin
Hi,
Problems with a washing machine not spinning or not draining are often interrelated..
If you are having a problem with your top load washer then check out thistip...
Washing Machine does not Pump or Spin
If you are having problems with your front load washing machine then checkoutthis tip...
Front Load Washing machine not draining and or not spinning
heatman101
3/27/2011 6:29:08 PM •
Hoover H130E...
•
Answered
on Mar 27, 2011
•
187 views
When sprining the mechine have
Usually over a period of use the washer tends to get out of balance, and then make more noise when it get to the spin cycle. I would suggest leveling the washer and then trying it out. The best way to fix this issue is by getting yourself a water level, u can get it in any hardware store. I personally would recommend a small circular water level for this job. Place the water level on top of the washer; make sure it is in the center. Take a look at the level and see where the bubble is in the water level? Accordingly you have to lower or raise either 4 corners of the washer to bring the bubble in the water level to the center. Now you have to be very gentle and small increments when rising or lower the corners of the washer, it does not take too much to move the bubble in the center.
If the problem continues then you have to open the top cover and check inside. 9 out of 10 the washer needs to be leveled.
8/10/2010 12:31:24 AM •
Hoover H130E...
•
Answered
on Aug 10, 2010
•
56 views
My hoover washing machine 1400 spin 8kg hd vision hd
Hi On my washer when I press the start button when allready in opperation all the lkights flash and it stops as this second press of the button pauses the machine and need the start button to be pressed again to restart the machine
Hope that is cleas and helps
Angela
8/15/2009 9:22:20 PM •
Hoover H130E...
•
Answered
on Aug 15, 2009
•
1,658 views
I have a hoover hsp15
The filter on most hoover machines is behind the kick plate at bottom front of machine.
Post back if further assistance required.
Thanks for using fixya.
7/13/2009 11:03:41 AM •
Hoover H130E...
•
Answered
on Jul 13, 2009
•
808 views
L g washer
is water still in the machine. if so check the pump (the little door at the base of the machine) first use that little tube to drain the water. there is a safety feature on front load washers that does not allow the washer to open if it is full of water
1/15/2009 4:09:28 AM •
Hoover H130E...
•
Answered
on Jan 15, 2009
•
162 views
Water not getting to powder dept
SMALL SPRING HAD COME LEVER THAT IS CONNECTED TO WATER RELEASE VALVE , RECONNECTED SPRING AND EVERYTHING SEEMS TO BE WORKING OK .
10/9/2008 12:20:41 PM •
Hoover H130E...
•
Answered
on Oct 09, 2008
•
206 views
Very noisy spin
sounds like you have a broken stanchion on the rear of the basket,usually a fatal diagnosis because price of repair excess cost of new one.check your manual and look under warranty.if you have a extended warranty on parts(stainless steel basket and tub)you would only have to pay for labor...good luck
9/29/2008 3:16:48 AM •
Hoover H130E...
•
Answered
on Sep 29, 2008
•
145 views
Not finding what you are looking for?