Top 20 Hoover AAA160 Front Load Washer - Page 5 Questions & Answers

Usually the bearing is a press fit as is the pulley.To be sure of not damaging it, contact a domestic appliance repair shop for assistance and you could get some idea of how to do it and the tools required but it will probably be cheaper to replace the machine.Don't forget, Hoover have a 10 year parts guarantee.

I would say check for a fuse blown. Not in your panel, but in the machine. These fuses could be bolt up or inline. But will always be accessible. Shine a light through it and it should make a solid and visible connection. If not, that's your culprit.

Very often the service guide and wiring diagram is hidden in the top console or in the upper part of the body stuck to the wall is a plastic bag. There might be a Service Manual, but you need the numerical model number rather than the fancy name '500'. https://www.google.com/search?q=hoover+500+washing+machine+service+manual ..

Turn it off at the mains. Leave it an hour and start again. Here is your manual in case you need it https://www.manua.ls/hoover/hn-6135/manual and even a 1 hour video :>)

Hoover Nextra HNWF6135 Washer Dryer - YouTube

https://www.youtube.com > watch 1:03:21 this is another of your choice! hoover nextra doing a cotton 40. please take a look at my amazon.

Too many clothes, not enough water, usually. However, this is a known issue on this Australian Washer. Throw it out, and buy a Front Loader. They take more laundry, use less water and electricity and don't tangle. https://www.google.com/search?q=HOOVER+500MB+WASHING+MACHINE+tangles+clothes ..

Crackling certainly doesn't sound good. How many days past warranty. Contact them, " 2 weeks ago my washing machine stopped working, I was going on a business trip, and couldn't do anything about it. I checked the fuse and it had blown. I replaced the fuse and it still doesn't work. When the machine failed it was in warranty, please come and fix". If not, the most likely issue for 'crackling' would be the control board or the motor, leaning slightly to the control board as it has no power visible to it. A failed motor would have power to the board, but nothing happening.

Faulty control panel

There is a common issue with those machines and the wiring harness, when the machine spins, the drum causes the wire harness to flex and vibrate and this can cause the wires to break loose. To check this you need to unhook and unplug the unit and drain it, Then you can lay it down and look under it to see what is causing the issue;

COULD BE ANY NUMBER OF THINGS. CONTROL BOARD . MOTOR , TRANSMISSIN, CALL A LOCAL REPAIR SERVICE

Error code E01 indicates a defective door latch or associated wiring or connection to control board.

Possibly the control board is failed.

I would suspect the transmission has gone out .but with out any testing no one can ever be sure

Most likely is the lid lock. Logic board will not allow spin to take place if the lid is not locked.

CONTACT A DEALER OF THAT MAKE

https://www.espares.co.uk/advice/careandmaintenance/how-to-fix-an-e10-error-on-a-hoover-washing-machine ..

Your Hoover could have a stuck cycle timer, a defective control board, or failure of some controlled element, for example the pump.

https://service.hoover.co.uk/advice-centre/the-letter-h-and-a-number-has-appeared-in-the-display-of-the-washing-machin/

Either the door lock has failed or the wiring or the programmer has a problem. Removing the cabinet top should allow a view of the wiring, etc. Manipulating or removing the door lock from inside the cabinet isn't easy as often the retaining screws are accessible only when the door is open and carefully applied brute force is the last resort.

fixya does not sell Hoover parts. check with an appliance parts supplier or directly with Hoover.

https://www.youtube.com/watch?v=3R_RYO6jSOs E21. Canister fill pump triac faulty. Possible fault Wiring faulty; Electronic board faulty. https://www.how-to-repair.com/help/e21-e22-error-code-tumble-dryer-pump-fault-aeg-electrolux-zanussi-etc/