Top 20 Hoover 24 in. DT999 Free-Standing Dishwasher Questions & Answers

it could be leak from the drain hose or any other hose like water flow hose, or water level (pressure switch ) hose , check also that the unit does not make over [email protected]

I think it may be leaking at the pump. Pull it out from the wall take the back off it and watch it go through a cycle

It probably just has a build up in it, try taking a bowl and filling it with apple cider vinegar (you want cider vinegar because of the citric acid, you can also use tang or frozen o.j) then put the bowl full of vinegar on the lower rack in the dishwasher, do not just pour the vinegar into the dishwasher beacuse the dishwashers 1st cycle is too drain so it will all just drain out, then run the dishwashers heaviest cycle with nothing in the dishwasher but the bowl of vinegar. This will clear out all the debris and hard water deposits throughout the dishwasher. If it seems to clear up your problem try changing your dishwasher soap to Finish I work at a service company and have found this to be the best dishwasher soap on the market. Hope this helps.

Hi

If the water inlet valve is fine and it fills with water then the issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that fills the dishwasher lifts the float, and when it reaches a certain level, it acts as a trigger for the float switch. The float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher. A defective switch may interfere with dishwasher's filling and/or draining ability. Use voltmeter to test the switch. Set the device to the ohms setting x 1. Take each probe and touch them to one switch terminal each. This should produce a reading of either zero or infinity. Continue to touch the probes to the terminals, and press down on the switch's button. The reading should change to the opposite extreme. If the switch fails either of these tests, you should replace it. Hope this helps...please post back for further assistance.

Daniel

Mam ten sam problem, na programie 1,2 po oko?o godzinie prania jest E3, na 7-mym jest ok. Pompka sprawna. Je?li mo?e sz daj sygna? czy uda?o Ci si? rozwi?za? problem, Mail do mnie [email protected]

is your dishwasher connected to the hot water lead? is the heated dry on? or is there a control issue

Hi,
Check your heating element..

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

How to Replace the Dishwasher Heating Element

Dishwasher Maintenance

heatman101

Asker's Testimonial " explanation very clear. will give it a go and see how simple it was. thanks Ronnie " - ronnieshomes

Well I just did this (ew!)

basically it just pulls out of a slot downwards (when doors open) but there's not much space so I took out a few screws to free the door up a bit.

So - sitting with the machine in front of you and door open down towards you:

I took out the two machine screws that hold the door on to the spring/hinge mechanism. Those are the two on the side of the door near to the hinge/bottom.
I also took out 3 of the screws that screw the inside metal bit of the door on to the plastic fron of the door.

You'll notice that the springs then force the inside and outside of the door apart and you've got some free space to pull the bottom seal out of the metal door. Then clean everything and squeeze the new seal in.

You're probably not going to be able to thread it in from one end.

When you're putting those two machine screws back in you'll probably need to do the top screw (nearest you when door open) with the door almost closed so that the spring is most relaxed and will let you line up the two holes.

Hope that helps

The problem is hard water. www.dishwasherfilter.com has a great new product out that will solve this problem once and for all. It filters the water entering your dishwasher and leaves your dishes looking amazing. They even have a money guarantee if you are not completely satisfied. Check it out. You will love it.

The white residue could be water spots from hard water. They are most notably left on clear plastic glasses, clear glasses, and silverware. If your silverware is authentic sterling silver you shouldn't be washing it in the dishwasher anyways as this ruins it.------

The best advice for the hard water is to use jet dry there should be a dispenser for this on your dishwasher. The other solution is to use those oxi clean tablets or the cascade 2 in 1 gel packs. normally,this is caused by hard water. try using a dying agent like jet dry, it will stop the white spots. good luck.--------
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

It is now apparent that the water is not coming from the dishwasher but from a back-up of frozen pipes in the extreme weather.

I now await a thaw!!

be sure flood control float is in place ..under rack..check flood control switch under bottom of dishwasher...check inlet valve and timer
thumbs up

Hi well check the following 1.discharge hose is not bent. 2.Filters are not blocked. 3.Syphon is not blocked
Thanks! mannu_rakesh

its possible that your timer has a bad contack at this spot the machine stops but the drain valves open try advancing the timer one notch to see if it will work if yes relace the timer thanks from gilles

I have done this on another make, but most front loading are very similar see pictures and solution here:
http://www.howtofixanything.co.uk/howto-260.html

your chopper is the culprite.you have to take the insides out of the dishwasher to locate the chopper.

few things to check for is the lower wash arm spinging freely if is is not turning properly it will cause the arm to spray in the corners also make sure there is no obstucktion in the wash arm all the small holes must be clear neck check your door gasket if not all flatened out thanks from gilles

Replace water softner seals (Hoover spares reference: 91941698) as stated previously. Harraps were doing them for £6 each. The softner is accessed by removing the R/H panel and unscrewing the air break ring nut from inside the machine. They are not a standard size so oem o rings are recommended.

check the ellement the ellement is normally used at the end of rinse foe sanitising the dish maybe shorting out at the connection below remove bottom pane obsrv it ewhen in the area where it happens to see if no drips fall on the conection or short a t te connecters of the ellement thanks from gilles