20 Most Recent Fisher and Paykel GWL11 Top Load Washer - Page 4 Questions & Answers

After filling with a small amount of water it will recirculate for a while then fill again to a higher level. To recirculate the divertor has to heat up and expand the operating plunger. It takes a long time to cool & move back to the drain position. You may be advancing from recirculate to drain too quickly. Allow at least 2 minutes before trying to drain water.

Check your belt it may be lose. A lose belt will cause a squealing noise and the machine spin slower or take time to come up to full speed

you have to check all the harness connections on this machine and when you realize that this is going to happen often you may want to consider tossing this in a dumpster.

Fisher and Paykel GWL11 Top Loading Washer

ths.gardenweb.com > Home Forums > Laundry Room

Mar 5, 2008 - My GWL11 Top loading washer has had nothing but problems! ... 4) (Rinse Phase) Drain the water, then lock the lid for spin. ..... I plug the power cord in and I have nothing on the control panel. ..... As the controller was only replaced early in January, I've flicked F&P NZ an email to see if it's still under ...

How to repair a Fisher Paykel Washing Machine

www.instructables.com/.../How-to-repair-a-Fisher-Paykel-W...

InstructablesI removed the pump and control panel, found no blockage in the pump, so far ... Ihave just tried to fill my F/P machine but the water is just dripping in. ... I have aFisher Paykel washer have replaced the control module and now it .... washing machine MW612, stopped working and displayed beeping sound every second.

Drain the machine. Then turn power is off at the wall socket. Then tip machine back against the wall as far as you can. Get down under front right of machine & remove the wires going to the drain pump. Next remove the drain pump by turning it 90 deg clockwise. There is a white clip near the top edge of pump on R.H. side - hold that out while you turn it. Once it is out check pump & up in the pump outlet hole for obstructions. Put pump back with wiring plug facing R.H.side of cabinet then rotate 90 deg anti clockwise. Re attach wires and stand machine up.

u need a new cold water valve, if u check the temp of the water while its filling it is mainly hot, or u have the hot nd cold hoses on the wrong way , as all rinses r cold

Small leak/drip with Fisher & Paykel GWL11 Washer (with ...

ths.gardenweb.com > Home Forums > Laundry Room

May 6, 2008 - Got a small drip/leak with my GWL11 washer..... The washer is ...Small leak/drip with Fisher & Paykel GWL11 Washer (with pictures) ..... New project for a new year: Light a fire under plans for an outdoor oven and claim the best pizza in town ... Speed Queen Front Load AFN50 Washer Review - Long Post.

Fisher and Paykel GWL11 Top Loading Washer

ths.gardenweb.com > Home Forums > Laundry Room

Mar 5, 2008 - My GWL11 Top loading washer has had nothing but problems! ... I have a Fisher Paykel GWL11 that I purchased new and have loved until this problem started. ... The machine fills with a small amount of water to saturate the clothes ...... Fault 36 is related to water leaking, but is *not* the kind of leaking from ...

Fisher and Paykel GWL11 Top Load Washer - faqqq

www.faqqq.com/.../fisher-paykel-gwl11-washer-leaking-and-squealing-fish... Question Product: Fisher and Paykel GWL11 Top Load Washer Question Details:Fisher Paykel ... Small leak/drip with Fisher & Paykel GWL11 Washer (with .

turn off water to machine, remove cold water hose and clean mesh screen on water valve and on the hose itself if present. If this didn't help - replace water valve.

get a technician in as the smell indicates a major problem

check out the DRAIN MOTOR PUMP , its a small motor with 2 hoses connected to it , it could be clogged , need to remove it , inspect inside the impellers for any debri , clean it , re install and try again , hope this helpful AJ

Hi just read your posting.Now when the machine starts beeping a series of lights will light up.These lights will be in a row of 8 lights.Starting from the left to right which lights are lit when the machine is beeping,Is it the 2nd and 4th or the 1st and 7th ---etc---?Please reply with additional information and I am sure I can help you.Looking forward to your reply.

130 indicates a faulty Rotor Position Sensor (RPS) or a bad connection to the RPS. This can be a common fault on all Smart Drives. Rather than explain the the procedure you can watch this video which a kiwi guy has done on how to fix it if you are good with that sort of thing. IF you live in NZ the best deal to get a new RPS is Rotorua Appliances or search TradeMe for RPS. To watch the video click the link. Good luck https://www.youtube.com/watch?v=6FQc64aBzc0 Fisher and Paykel 130 10000010 Error Code Fix

dear plz follow this video may be this one help you

What kind of capacitor is c455? IT should be marked with something that tells what it is. Also it might just be the capacitor failed. They do that a lot now with the cut rate capacitors on the market.

What lights come on? If it is a constant beep then may need a new mother board

sounds like code 130 position sensor in motor ,probably won't spin either

take clothes out,check the hose for is it blocked or kinked put a clothes hanger in hose and see if you can un-snake any thing out,then put draino-max jel in washer and let it set for about 2-3hrs,see there may be hair blocking the pump were it drains,this stuff work great for front-loader so let it sit.then try putting on drain it may take a few times,the when it drains,run washer on full cycle no clothes hot-water let it go through a full wash cycle etc.

Your pump and drain pipe could be blocked. Check for squashed drain pipe. Switch off power and water taps Bail out all water you can with cup move machine out from wall tilt machine back on a wall to look under to find pump. push white pump retainer clip outwards and turn pump anticlockwise to remove. and check for item in the impeller.

Water Valve Test When in Diagnostic Mode, the WASH TEMP UP button turns the hot water valve on. The Hot LED is on when the hot valve is on. The WASH TEMP DOWN button turns the cold water valve on. The Cold LED is on when the cold valve is on. DIAGNOSTIC MODE Turn the power on at the power point but off at the machine. Press and hold the WASH TEMP DOWN button and then the POWER button until the machine gives 2 short beeps and lights up. Release buttons when the beeps indicate diagnostic mode has been entered. There maybe up to 3 filters cold water line. There is sometimes 1 at each end of the water hose itself and also in the valve which can be removed with pliers. (see picture) Undo the 2 screws at the back of the buttons panel Undo the connection of the valve If you are good with a multimeter check that there is about 65 ohms resistance across the terminals of the valve. If not, then replace the valve. Also sometimes the workings inside the valve can jam shut so replace the valve.