20 Most Recent Denon DVD-900 DVD Player - Page 6 Questions & Answers


All the disks I've tried have, although it's only been 3 or 4 (both home-made and original). It sounds like the motor and/or the head moving around. Next week I'll go to the store I got it from and bring a DVD is particularly noisey in the drive, and try it in their floor model to see if it's this particular unit or the model in general.


Parts Of BMW.

Denon Televison... | Answered on May 30, 2012


Usually it is a setting in the menu somewhere that causes this--if all else fails read the owner manual cover to cover.

I have seen several with this issue and all were a setting wrong.

Denon Televison... | Answered on May 29, 2012


Step 1:

Check the light on the remote
, press a number. If the light is on, go to step 4. Not light, then go to step 2.
Step 2:

Check the batteries
Make sure the batteries are full and correct in the remote control. If the batteries are full and correct in the remote control, but the remote still does not work, go to Step 3.
Step 3:

Connect the metal parts

Note:
The lower steps are only for the short remote control, see Fig. Do you have a long remote, go to step 4.

  • Take the battery cover
  • Connect the metal parts with a screwdriver or paper clip.Replace the batteries and check that your remote works again.

    It may be that your remote control needs to be reset for use with your TV.


    Step 4:

    Restart the TV receiver

    • Turn on the television receiver in standby mode by pressing the i-TV (top right).
    • Leave the TV receiver 30 seconds as they are.
    • Unplug the TV receiver from the mains.
    • Plug after 10 seconds into the socket.
    • Turn on the TV receiver by pressing the i-TV (top right).
  • Porsche Parts

Denon Televison... | Answered on May 27, 2012


please clean the contact batteries and spray the contact with special spray contact. Retight the springs for better contacts batteries. See if there are some loose or desolder wire.

Otherwise you must open the remote, and see inside for defective components, or coold solder. Resolder.

sincerely. God bless you

Denon Televison... | Answered on May 07, 2012


Change the HDMI cable, and test on second TV.

Denon Televison... | Answered on Mar 22, 2012


disk reading failure you can try to clean the optical lens by wipeng it with a cotton buds moisten with an alcohol..check also the ribbon wire that connects between the lens and the mainboard make sure that the ribbon is intact with no broken lines and perfectly fits to the socket.re attached all the connectors from the board..good luck hope this helps you..

Denon Televison... | Answered on Feb 21, 2011


Try website like Remotes.com to buy an exact remote to the original remote.

Denon Televison... | Answered on Nov 15, 2010


Hi have you try to open the remote and clean it inside sheet rubber and pcboard use alcool and tooth brush then maked dry make shure theres no residu left on contact sheet and board..
hope that will hell you...

regards alan

Denon Televison... | Answered on Oct 21, 2010


Hi,

It seems that there has been an issue with IR sensor.In most of the cases, investing in new remote is a wise option. However, as you have already changed the batteries, few more simple steps you could follow :-

1. Try to use the remote from close.

2. Clean the battery connectors. Most of the times, you might find dirt and debris out there.

3. Dissemble the remote. Clean the sensor and the keypad and then reassemble it.

If you wish to repair it, i would be glad to help. However, as i said the cost of repair is usually more than investing in new remote .

I hope i have been helpful.

Thank You!!

Denon Televison... | Answered on Aug 21, 2010


It is possible that the detect sensors are malfunctioning result in the false trigger of the input detector. So in the first place open the front loading section and clean up the CD take up section. Notice the optocoupler sensors which are the cd detect sensors that could be the culprit in this case. Use a multimeter to check for action on the sensor by blocking and confirming for changes in voltage. If so replace the unit. If not you must also check the mechanism for possible misalingment. remove carefully the mechanism and reset after cleaning. Get help if you are not familiar but be very delicate to do this job if inexperienced. Hope you try with care. Good day

Denon Televison... | Answered on Aug 03, 2010


Hello i have got a all for one remote control and i want to use it for a hitachi freeview box have u got the codes for it plz. thanxs stphen

Denon Televison... | Answered on Feb 14, 2010


From my experience, most of the Denon remotes are universal and do work with each other. If anything, make sure it has a 30 day warranty so you can always exchange it or get a refund.

Denon Televison... | Answered on Feb 09, 2010


with Denon you have to go into the menu and "assign" the inputs.

You have to select if you are using HDMI, s-video composite etc.

If your unit has upconverting remember that it will upconvert a s-video signal to HDMI but not the other way around.

HDMI is a digital signal composite, s-video etc are analog therefore you could not use the HDMI output from your PS3 but then use the red, blue green composite outputs from your receiver to run to your tv.

Denon Televison... | Answered on Dec 30, 2009

Not finding what you are looking for?
Denon DVD-900 DVD Player Logo

Popular Tags

7 questions posted

Ask a Question

Usually answered in minutes!

Top Denon Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76177 Answers

Ekse

Level 3 Expert

13434 Answers

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

Are you a Denon Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Denon Televison & Video

  • Denon Televison & Video

Most Popular Question

dvd player will no longer turn

  • Televison & Video
Loading...