20 Most Recent
Maytag MAH6700AWW Neptune Front-Load Washer - Page 4 Questions & Answers
Code nd
Don't know if this is your problem but sometimes ours will appear to drain, but there is still a lot of suds that remains and trips the nd (no drain) indicator/lockout. We had to pour water in from a bucket to beat down the suds, then repeat several times to get all the suds out. First time I took off the back of the washer, disconnected the pump, then let the suds out. To much work.
11/14/2013 4:00:05 AM •
Maytag...
•
Answered
on Nov 14, 2013
Reset neptune
How can i reset my toshiba e studio120 photocopier machine?
10/30/2013 9:25:21 AM •
Maytag...
•
Answered
on Oct 30, 2013
Maytag Neptune door lock stuck!!!
Try these steps:
1.) Take the washer outside. 2.) Loosen the two screws on the back panel and remove the back panel. The pump sits on the left-side of the opening. There's a black water hose with a metal clamp; 3.) squeeze the metal clamp with your fingers until it's loose enough to slide away from the pump. 4.) Separate the hose from pump and the trapped water will pour out and the door will then open; and 5.) clear any blockage from the drain hose and the pump.
8/12/2013 12:32:55 AM •
Maytag...
•
Answered
on Aug 12, 2013
Maytag Washer Drum is broken, how do we remove it
Model numbers help us tremendously.
I believe this Factory Service Manual covers your machine.
If not,give a model number for a more specific manual.
cut and paste this link:
http://www.servicematters.com/maytag_library/docs/16023110.pdf
8/4/2013 8:40:38 PM •
Maytag...
•
Answered
on Aug 04, 2013
Maytag 4000 series error code
Hi
Thanks
for using FixYa. Please post a comment with the
model no# for your Maytag 4000 series washer so that I can assist you further.
Thanks
Rylee
5/5/2013 3:25:07 PM •
Maytag...
•
Answered
on May 05, 2013
Water leaks from softner dispenser
I had same thing with MtgNeptune frnt loader. Manual sed may be a kink in the front drain hose, caused by sudden burst in water pressure. Not in my case. A service call and $90 laterwasn't fixed. I pulled the soap tray and found rinse water wasn't going down the well as fast as it was filling, causing water to spill down front, and around the door. I turned down the water pressure 2 days ago and 9 loads later- no problem! It may take a few minutes longer to fill, but far less work than mopping after each load or hitting 'pause' and 'start' while waiting for the the water level to go down. We're on a well and ocassionally have change in water pressure. I don't know if this was the problem, but it was definately my solution! I turned the intake vavles at the wall to 1/2 pressure. Floor is staying dry and the drain tray beneath is also dry ($12.00 Menards). I hope this helps.
4/7/2013 10:32:44 PM •
Maytag...
•
Answered
on Apr 07, 2013
Water Leaking really bad from the Dispenser area
Disconnect the plug from the outlet. Remove the top of the washer panel by removing the 2 back hex screws then sliding it back to lift it off of the washer. Take off the front control panel by removing the phillips screws holding it in place. Remove the dispenser drawer. Check the dispenser housing for clogs or lime build up at the bottom of the dispenser housing. Or the drain hose (large black hose attached to the front of the drawer housing) to the washer may be crimped or clogged.
4/7/2013 10:23:40 PM •
Maytag...
•
Answered
on Apr 07, 2013
Not finding what you are looking for?