Kyocera Mita FS-1030D Laser Printer - Answered Questions & Fixed issues
Ther is a toner but it shows toner is low
Maybe by this time you have already discovered that you needed a new toner fast if specially you're making many copies. It just lets you know that you will need a new toner soon.
5/10/2013 5:27:36 PM •
Kyocera Mita...
•
Answered
on May 10, 2013
•
63 views
Do not print when the page is landscape oreintation
Ok just make sure when you press the print order to have the correct selections: the correct printer and in that same menu you have selected the orientation of the paper which would be landscape. there should be no problem.
5/10/2013 2:03:05 AM •
Kyocera Mita...
•
Answered
on May 10, 2013
•
89 views
Constant paper jams
find some hard paper like trancparency plastic paper or some hard type paper leke certeficate printing paper and by opening the tray out and push the paper till u see it out around the touner cartirage place after doing so replace the tray and the toner cartirage hop the printer do not paper!!!
5/9/2013 10:17:41 PM •
Kyocera Mita...
•
Answered
on May 09, 2013
•
149 views
Kyocera fs 1030d: first sequence: 1.led:green
THE PROBLEM IS THE FUSER, YOU HAVE TO OPEN THE ENTIRE TEAM AND IN THE BACK OF PART WHERE IS HEATS UP THE PAGE, BETWEEN ROLLER GREY AND ORANGE, ALLI THIS FUSER. HIM REMOVING THE ENTIRE PIECE THIS SUBJECT TO TWO SCREWS, YOU MUST DISCONNECT THE CABLES (THREE PAIRS), THE PIECE THAT YOU JUST EXTRACTED HAS TWO SCREWS THAT HOLD A BONBILLO THAT IS INSIDE THE GRAY CYLINDER, THERE BELOW YOU WILL SEE A SMALL WHITE PIECE THAT IS SUSTAINED BY TWO SCREW WHICH ARRIVE TWO CABLES, THE DRAW AND THEN TO THE WHITE PIECE WITH A FINE NEEDLE HIM GOING TO PASS UNDERNEATH AND CAREFULLY RAISE THE BLACK PARTIF THE VERIVICAS SHOULD GIVE CONTINUITY WITH EN MULTIMETRO O METER OF VOLTAGE. IF YOU WANT THE CAN BUY ALSO IN AN ELECTRONICA.
SORRY ENGLISH
12/28/2011 9:57:28 PM •
Kyocera Mita...
•
Answered
on Dec 28, 2011
•
240 views
Can you help me with kyocera fs-1030d
If a paper jam occurs while printing, the printer notifies it by the following combination of the four indicators. Remove the
jammed paper . After removal, open and close the top cover once to initialize the jam sensing
12/22/2011 5:13:09 PM •
Kyocera Mita...
•
Answered
on Dec 22, 2011
•
1,643 views
Fs-1030
This is a Thermostate problem. You have to reset thermostate or replace the fuser unit your problem will resolve.
3/7/2011 3:56:33 PM •
Kyocera Mita...
•
Answered
on Mar 07, 2011
•
1,383 views
I was cleaning the drum
I think you are going to have to purchase a new drum unit because they don't spare the parts.
3/2/2011 8:18:07 PM •
Kyocera Mita...
•
Answered
on Mar 02, 2011
•
171 views
KYOCERA FS-1030D - 3rd Light from top is Red
this is problem with cassate please add paper in cassate.
* in cassate at last one green color botton is there set that one as per paer size
* after remove the cassate see at front left down there one white color sensor is there this sensor senseing the cassate availbilty please check that one
* while inserting cassate insert slowly
2/18/2010 2:47:06 AM •
Kyocera Mita...
•
Answered
on Feb 18, 2010
•
926 views
Not finding what you are looking for?