20 Most Recent
Whirlpool Duet GHW9150P Front Load Washer - Page 2 Questions & Answers
F12 won't drain or
Hi, i'm pretty sure that this would seem to suggest that the pump maybe faulty or that there is a blockage, arm yourself with a large bucket or bowl and take the drain hose from the machine gently lowering it to below the washing machine tub level, make sure the drain hoseis quite flat or level as you do this, lift the hose if you need to stop the water because the bucket is full, empty the bucket and start again until no more water runs, then set about checking the filter for blockages or anything that maybe fouling the pump, if all is clear then it could be a suspect pump,if not clear all debris clean the filter re-insert it and make sure the drain hose is back in place, try the machine on a cycle,let it fill and see if it empties(pump runs), if not, the machine will not take in any further fresh water or do a main spin because there is water trapped in the machine. so you will have to go through the manual drain procedure again as above and try a new pump, there is also the possiblity it could be the main control board or faulty control loom.
If in doubt look for a washing machine technician that maybe able to give you a free quote.
Hope this helps.
I get an f06 and
F6
code is an issue with the motor drive tachometer.
Most often this is caused
by poor connections at the machine control or motor controller. Locate
the main machine control by removing the top panel and the motor control
by removing the rear panel. Remove each connector, one at time, and
reinstall. If this does not work, you likely have a faulty control.
E1
means that the thermistor is open and needs to be replaced.
The connections can be loose but the most likely cause of an E1 error is
a bad thermistor.
If you're comfortable and confident in your
do-it-yourself skills and have access to a volt/ohm meter you can check
and replace this part yourself.
For replacement parts - head on
over to SearsPartsDirect.com - PartSelect.com - or RepairClinic.com and
enter in your full model number for a full parts listing.
Hope helps.
My Whirlpool washer flashed F30. Not filling up with water.
Hi,
"F30" indicates "DISPENSER SYSTEM ERROR"
When the dispenser motor cannot be driven to its proper position this error appears in your washer. To fix this problem follow these procedures.
1. Unplug washer or disconnect power.
2. Check mechanical linkage from dispenser motor to the top of the dispenser.
3. Check wire harness connections to the dispenser motor and Central Control Unit (CCU).
4. Check dispenser motor for powered rotations.
Thank you !!
Whirlpool front loading duet washer
Hello
Error F31 in your whirlpool duet washer is displayed due to MCU (Motor Control Unit) failure. It is displayed if the heat sink gets too hot and then the MCU stops motor, then MCU sends the signal to CCU (Central control unit). Please check the wire connections between the CCU and MCU, if thats fine then check the motor operation. Hope you understand...replacing the part# that has gone bad is recommended repair. Please get back to me if you have any other questions.
Kevin
F05 error code comes on
Water Temperature Sensor Error - Check the Water Temperature Sensor,Heating Element and Element Relay.
If during the water heating step in wash cycle,the water temperature sensor(NTC) value is out of range,or the heating element circuit has failed,the F05 error code will be displayed - Check connections to
the Sensor,Heating Element and Relay.
How do i reset front panel on my whirlpool washer
Hi
Its a simple procedure to reset the Whirlpool Duet front load. Please press and hold the END OF CYCLE button for 15 seconds to reset. Please get back to me if you have any other questions.
Kevin
Error Code F8E1 on Whirlpool Duet
f8 is shown when the heater circuit is on with no water in.. it doesnt do it when you unplug the pressure switch because your disabling the heat protect circuit
THE BOARD IS PROBABLY FAULTY
F08 indicates pressure switch stuck on full.
Unplug the appliance from the wall socket.
Take the top off the machine.
Locate the pressure switch, you can identify it by the thin tube attached to it.
Take the tube off, blow down this tube as hard as you can to shift any blockage or restriction in the pressure chamber. Give the pressure switch a couple of good taps with the screwdriver handle.
Refit the tube and try the machine again.
If still doing it, unplug again and follow the tube down.
This end will be attached to the pressure chamber.
Take this chamber off and thoroughly clean it out, clean out the port into the tub too.
Reassemble and try again.
If after this it's still faulty you'll need to start replacing parts.
I'd suggest trying a new pressure switch first.
Failing this, if all of the above fails to resolve the problem you're possibly looking at a faulty main control board.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
Our Clothes smell musty and the washer smells too
clogged water screens , defective water level pressure switch , clogged drain, kinked drain hose ,. defective water pump , defective water tempeerture switch, damaged water valve solenoid , water inlet valve has an interal malfunction
My Whirlpool Duet Front Load Washing Machine is
F28 is a communication error which usually means there is a connection that has come loose. Removing the top and unpplugging and replugging the connectors in will fix 75% of these codes. If the bottom toe panel is not on it will also give you an F28
Unplug or turn the circuit breaker off for 30 seconds.
Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.
Press the Pause/Cancel/Stop button twice to clear the display.
Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts if you have any further questions message me back and please remember to rank how this opinion has helped in your appliance situation when our chat has concluded Thanks again Rick
The control locked button is on and the washer is
Hello & Welcome to FixYa
Your whirlpool duet washer needs a reset to resolve the control lock problem. Press and hold the END OF CYCLE button for 15 seconds to reset the control. Please get back to me if you have any other questions.
Kevin
Washing machine turns off after pushing start button
Hi,
After about year and half Whirlpool duet sport gave F01 error code. The
technician manual is located under the lower front panel. There are
three possible reasons for F0:
1) EEPROM ERROOR. Unplug a washer for two minutes. Try running it again.
(Did not work for me).
2) MAIN RELAYS ERROR. The tech manual suggests replacing CCU. The
following is what I did and it fixed the problem, however. Unplug the
washer. Remove the top cover by removing the three screws on the back.
The CCU unit is in the right bottom corner if standing in front of the
washer – it has a lot of wiring. Plug in the unit. While
listening to the CCU start any washing cycle. After pressing START you
should hear the relay to click. If it clicks twice, within a less than a
second, it has a problem. Unplug the washer. Without disconnecting any
wires remove the CCU cage from the washer wall. Stand now on the right
hand side of the washer in such way that the CCU cage is under your left
hand. Pull the right upper corner of the CCU plastic cage (it has a
tab) away from you, slide the cage to the right by about an inch, and
pull the entire cage away from you. Now knock on the back side of the
cage 4-5 times with a bit of force.
Install the CCU cage back. Plug in the unit. Try some washing cycle
again. If it did not help, repeat the procedure. If it did not work
again, see the following.
3) PUMP DRIVE ERROR. The tech manual suggests replacing CCU.
We just purchased a Maytag Elite series washer
Cawnee:
Thank you for your review.
We would like to inquire further about your review with you. Please respond back to this email address,
[email protected], with your name, phone number, street address, zip code, model & serial number, and date of purchase on the appliance.
We look forward to your reply.
Thank you,
Maytag® Social Media Relations
Not finding what you are looking for?